Keep your GE GTW335ASN2WW washing machine running reliably with genuine OEM replacement parts from Repair Clinic. The GTW335ASN2WW is a 4.2 cubic foot top-load washing machine in GE’s GTW series. The N2WW suffix identifies the specific production revision; the related GTW335ASN1WW is the prior revision of the same platform, and most service components are shared between the N1WW and N2WW revisions. Parts most frequently replaced include the lid lock assembly, drive belt, water inlet valve, and control board. Use the GTW335ASN2WW parts list and browse the full GE washer parts catalog.
GE GTW335ASN2WW on the GTW Platform: 4.2 Cu. Ft. Top-Load Architecture, N2WW Revision, and N1WW Cross-Reference
The GE GTW335ASN2WW is a 4.2 cubic foot top-load washer in GE’s GTW series with a stainless steel wash basket. The N2WW suffix identifies this as a second revision of the GTW335ASN platform; the GTW335ASN1WW is the prior revision at the same platform. Most service components including the lid lock, drive belt, water inlet valve, and agitator are interchangeable between the GTW335ASN1WW and GTW335ASN2WW. The GE GTW335ASN2WW uses an electronic lid lock that must sense a closed and locked lid before any wash cycle can begin; a failed lid lock is the most common cause of a GTW335ASN2WW that will not start a wash cycle. For diagnostic guidance, visit the GE washer repair help section.
GTW335ASN2WW Component Failures and Diagnostic Sequences
GTW335ASN2WW Lid Lock Failure and No-Start Diagnosis
The GTW335ASN2WW lid lock is an electronic locking assembly that both physically locks the lid and sends a closed-lid confirmation signal to the control board before each wash cycle. A failed lid lock prevents the cycle from starting because the control board does not receive the closed confirmation signal; the washer powers on but will not advance past the cycle selection stage. Test the lid lock for continuity in both the lock solenoid circuit and the door-closed switch circuit before replacing the control board for any no-start complaint. Browse GE washer lid lock parts.
GTW335ASN2WW Drive Belt Wear and Agitator or Spin Failure
The GTW335ASN2WW drive belt connects the motor to the transmission and agitator shaft. A worn or broken belt causes the agitator to stop moving or the drum to fail to reach spin speed; the motor continues to run normally while the agitator or drum does not respond. Confirm the belt condition by accessing the motor compartment and inspecting the belt for cracking, glazing, or breakage. Browse GE washer drive belt parts.
GTW335ASN2WW Water Inlet Valve and Fill Diagnosis
The GTW335ASN2WW water inlet valve controls hot and cold water flow into the tub. A failed valve solenoid prevents filling (the washer attempts to fill but no water enters) or allows continuous filling when power is off (a valve stuck open). Test the inlet valve solenoid coils for continuity before replacement; each solenoid can fail independently. Browse GE washer water inlet valve parts.
GTW335ASN2WW Agitator Replacement and Inspection
The GTW335ASN2WW agitator moves laundry through the wash water during the wash cycle. An agitator that spins freely in one direction without moving laundry has worn agitator dogs (the cam-and-ratchet mechanism that converts oscillating motion to one-directional agitation); inspect the agitator dogs before replacing the full agitator assembly.
GE GTW335ASN2WW Parts at Repair Clinic
- Genuine GE OEM Parts for the GTW335ASN Platform: Every GTW335ASN2WW part meets GE original equipment specifications. Browse the full GE washer parts catalog.
- GTW335ASN1WW and GTW335ASN2WW Cross-Reference: Our listings confirm which components are shared across the N1WW and N2WW revisions.
- Lid Lock First Diagnostic Guidance: Our content documents the lid lock as the first component to test for no-start complaints on the GTW335ASN2WW.
- Fast Shipping: In-stock GTW335ASN2WW parts ship promptly, supported by the GE washer repair help section.
GE GTW335ASN2WW Washer Parts FAQ
What type of washing machine is the GE GTW335ASN2WW?
The GE GTW335ASN2WW is a 4.2 cubic foot top-load washing machine with a stainless steel wash basket. It uses a traditional agitator design with an electronic lid lock and a belt-driven transmission. The N2WW suffix identifies this as the second production revision of the GTW335ASN platform; it is closely related to the GTW335ASN1WW with most service components interchangeable between the two revisions.
Are GTW335ASN1WW and GTW335ASN2WW parts interchangeable?
Most service components including the lid lock, drive belt, water inlet valve, agitator, and control board are interchangeable between the GTW335ASN1WW and GTW335ASN2WW within the same GTW335ASN platform. The N1WW and N2WW suffixes identify consecutive production revisions; confirm part numbers from the GTW335ASN2WW specific parts list before ordering from N1WW listings for wiring harness and board-revision-specific components.
Why won’t my GE GTW335ASN2WW start a wash cycle?
A GTW335ASN2WW that powers on but will not start or advance a wash cycle most commonly has a failed lid lock assembly that is not sending the closed-lid confirmation signal to the control board. The control board requires a confirmed closed-and-locked lid signal before allowing any cycle to begin. Test the lid lock for continuity in both the solenoid and door-switch circuits before replacing the control board; a lid lock failure accounts for the majority of no-start complaints on this platform.
How do I check if the GTW335ASN2WW agitator dogs need replacement?
Remove the agitator cap and the agitator bolt to lift the agitator from the agitator shaft. Tip the agitator upside down and inspect the agitator dogs, which are small plastic cams inside the lower agitator body that engage with ratchet teeth during the wash stroke. Dogs that are worn flat, cracked, or missing cause the agitator to turn freely in one direction without engaging the laundry. Replace the agitator dog kit rather than the full agitator assembly when only the dogs are worn.
