Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool/Kenmore Washer Drain Pump Mounting Bracket #8546127
Whirlpool/Kenmore Washer Drain Pump Mounting Bracket #8546127
Skill Level
Total Parts Cost
$11.06Estimated Savings
$112.5002:40
- Description
This video provides step-by-step repair instructions for replacing the drain pump mounting bracket (or retainer clip) on a Whirlpool/Kenmore top-loading washing machine. The most common reasons for replacing the drain pump mounting bracket are when it is rusted or broken.
All of the information for this drain pump mounting bracket replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools needed: flathead screwdriver, Phillips head screwdriver, pliers, putty knife
All of the information for this drain pump mounting bracket replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools needed: flathead screwdriver, Phillips head screwdriver, pliers, putty knife
Step By Step Instructions
1
As with any repair, be sure you've unplugged the appliance before beginning.
2
Your first step is to move the control panel out of the way.
3
To do this, remove the screws found at either end.
4
On some models, these screws may be located in the rear panel or they may be covered by plastic end caps.
5
Pull the end cap off from the top to access the screw.
6
Remove both screws and rotate the panel up.
7
Some models use clips instead of screws to secure the control panel.
8
Insert a putty knife between the control panel and the cabinet to release the clips.
9
Unplug the wire connector and snap out the spring clips using a flathead screwdriver.
10
Tilt the cabinet towards you, slide forward, and remove.
11
You're now ready to remove the old retainer clip from the drain pump.
12
Using a flathead screwdriver, snap off the clip you wish to replace and rotate 90 degrees to remove.
13
Install the new retainer clip by inserting the tabbed end into the slot above or below the motor.
14
Rotate the clip 90 degrees and snap it onto the pump.
15
Now reinstall the cabinet.
16
The front edge of the cabinet slides underneath the base frame.
17
Use your foot to push it into position.
18
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
19
Now ease the cabinet to match up with the rear panel.
20
Reinstall the spring clips, reattach the wire connector, rotate the control panel down, and lock the clips into place or reinstall the two screws if applicable to your model.
21
Replace the end caps by aligning the tab with the slot at the bottom and snapping the cap into position.
22
You're now ready to plug the appliance back in to make sure it's functioning properly.
Description
This video provides step-by-step repair instructions for replacing the drain pump mounting bracket (or retainer clip) on a Whirlpool/Kenmore top-loading washing machine. The most common reasons for replacing the drain pump mounting bracket are when it is rusted or broken.
All of the information for this drain pump mounting bracket replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools needed: flathead screwdriver, Phillips head screwdriver, pliers, putty knife
All of the information for this drain pump mounting bracket replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Roper, Maytag, Estate, Inglis, Crosley, Amana, Admiral
Tools needed: flathead screwdriver, Phillips head screwdriver, pliers, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you've unplugged the appliance before beginning.
2
Your first step is to move the control panel out of the way.
3
To do this, remove the screws found at either end.
4
On some models, these screws may be located in the rear panel or they may be covered by plastic end caps.
5
Pull the end cap off from the top to access the screw.
6
Remove both screws and rotate the panel up.
7
Some models use clips instead of screws to secure the control panel.
8
Insert a putty knife between the control panel and the cabinet to release the clips.
9
Unplug the wire connector and snap out the spring clips using a flathead screwdriver.
10
Tilt the cabinet towards you, slide forward, and remove.
11
You're now ready to remove the old retainer clip from the drain pump.
12
Using a flathead screwdriver, snap off the clip you wish to replace and rotate 90 degrees to remove.
13
Install the new retainer clip by inserting the tabbed end into the slot above or below the motor.
14
Rotate the clip 90 degrees and snap it onto the pump.
15
Now reinstall the cabinet.
16
The front edge of the cabinet slides underneath the base frame.
17
Use your foot to push it into position.
18
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
19
Now ease the cabinet to match up with the rear panel.
20
Reinstall the spring clips, reattach the wire connector, rotate the control panel down, and lock the clips into place or reinstall the two screws if applicable to your model.
21
Replace the end caps by aligning the tab with the slot at the bottom and snapping the cap into position.
22
You're now ready to plug the appliance back in to make sure it's functioning properly.
Applicable Product Model
Parts Needed
Clip
$11.06
Total$0.00
Related Articles & Videos
04:10
Part Replacement
Washer Won't Spin? Replace Whirlpool Direct Drive Clutch Assembly Part # 285785
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com