Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairCraftsman Chainsaw Starter Rope Replacement #530069919
Craftsman Chainsaw Starter Rope Replacement #530069919
Skill Level
Total Parts Cost
$5.17Estimated Savings
$112.5004:24
- Description
This video provides step-by-step repair instructions for replacing the starter rope on a Craftsman chainsaw. The most common reason for replacing the starter rope is when it is broken or frayed.
All of the information for this starter rope replacement video is applicable to the following brands:
Craftsman
Tools needed: T-25 Torx bit screwdriver
All of the information for this starter rope replacement video is applicable to the following brands:
Craftsman
Tools needed: T-25 Torx bit screwdriver
Step By Step Instructions
1
Before you replace the starter rope in your chainsaw first make sure the engine has cooled. and that the on-off switch is in the “off” position.
2
Now use a t-25 torx bit screwdriver to remove the screws securing the starter assembly.
3
With the screws removed, pull off the assembly and set it on a sturdy surface.
4
If still intact, extend the starter rope and secure it then untie the knot securing the rope to the handle.
5
Remove the handle.
6
Now slowly release the tension on the recoil spring.
7
Use the t-25 torx bit screwdriver to remove the mounting screw securing the drive gear and pulley assembly.
8
Lift off the drive gear and drive spring and carefully remove the pulley to avoid dislodging the recoil spring.
9
Next, unwind the rope from the pulley.
10
Remove the screw securing the rope and pull the old rope free.
11
You’re now ready to install the new starter rope.
12
Insert one end of the new rope through the hole in the pulley align it on the pulley and secure it with the screw.
13
With the screw facing up, wind the rope clockwise around the pulley.
14
Carefully realign the pulley in the starter housing and rotate it clockwise until the pulley hooks onto the recoil spring.
15
Realign the drive spring and gear then thread and tighten the mounting screw.
16
Now rotate the pulley clockwise approximately two revolutions.
17
Insert the rope through the hole in the housing and secure.
18
Insert the rope through the handle and tie a knot at the end of the rope.
19
Reposition the starter assembly on the chainsaw and replace the screws to secure.
20
With the repair completed turn the on-off switch to the “on” position and your chainsaw should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the starter rope on a Craftsman chainsaw. The most common reason for replacing the starter rope is when it is broken or frayed.
All of the information for this starter rope replacement video is applicable to the following brands:
Craftsman
Tools needed: T-25 Torx bit screwdriver
All of the information for this starter rope replacement video is applicable to the following brands:
Craftsman
Tools needed: T-25 Torx bit screwdriver
Step-By-Step Instructions
1
Before you replace the starter rope in your chainsaw first make sure the engine has cooled. and that the on-off switch is in the “off” position.
2
Now use a t-25 torx bit screwdriver to remove the screws securing the starter assembly.
3
With the screws removed, pull off the assembly and set it on a sturdy surface.
4
If still intact, extend the starter rope and secure it then untie the knot securing the rope to the handle.
5
Remove the handle.
6
Now slowly release the tension on the recoil spring.
7
Use the t-25 torx bit screwdriver to remove the mounting screw securing the drive gear and pulley assembly.
8
Lift off the drive gear and drive spring and carefully remove the pulley to avoid dislodging the recoil spring.
9
Next, unwind the rope from the pulley.
10
Remove the screw securing the rope and pull the old rope free.
11
You’re now ready to install the new starter rope.
12
Insert one end of the new rope through the hole in the pulley align it on the pulley and secure it with the screw.
13
With the screw facing up, wind the rope clockwise around the pulley.
14
Carefully realign the pulley in the starter housing and rotate it clockwise until the pulley hooks onto the recoil spring.
15
Realign the drive spring and gear then thread and tighten the mounting screw.
16
Now rotate the pulley clockwise approximately two revolutions.
17
Insert the rope through the hole in the housing and secure.
18
Insert the rope through the handle and tie a knot at the end of the rope.
19
Reposition the starter assembly on the chainsaw and replace the screws to secure.
20
With the repair completed turn the on-off switch to the “on” position and your chainsaw should be ready for use.
Applicable Product Model
Parts Needed
Starter Rope
$5.17
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com