Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairHonda Small Engine Pump Gasket Replacement #16011-Z0H-013
Honda Small Engine Pump Gasket Replacement #16011-Z0H-013
Skill Level
Total Parts Cost
$5.92Estimated Savings
$112.5003:57
- Description
This video provides step-by-step instructions for replacing the pump gasket on Honda small engines. The most common reason for replacing the gasket is if it is damaged, causing the engine to run poorly or not start.
All of the information in this gasket replacement video is applicable to the following brands: Honda
Tools used: 8mm socket or nut driver, small flat-head screwdriver, Phillips head screwdriver
All of the information in this gasket replacement video is applicable to the following brands: Honda
Tools used: 8mm socket or nut driver, small flat-head screwdriver, Phillips head screwdriver
Step By Step Instructions
1
Before you replace the pump gasket in your engine’s carburetor first make sure the engine has cooled.
2
Now depress the tabs to release the air filter cover and pull out the filter element.
3
Use an 8mm socket or nut driver to unthread the mounting nuts securing the filter housing.
4
Remove the support plate and detach the housing from the breather tube.
5
Note the orientation of the fuel lines attached to the carburetor then detach them – be prepared for some fuel to spill out.
6
With the lines detached, slide the carburetor off of the mounting posts. and set it on a sturdy surface.
7
Use a phillips-head screwdriver to remove the screws holding the carburetor components together.
8
Carefully lift off the needle housing, metering cover and mounting plate assembly.
9
If still intact, separate the old gasket from the pump diaphragm.
10
When installing a new pump gasket we recommend using a new diaphragm as well.
11
Confirm that the spring is in place then align the new gasket on the tabs followed by the diaphragm.
12
Reposition the needle housing, the metering gasket and diaphragm along with the metering cover and mounting plate assembly.
13
Thread and tighten the screws to secure.
14
Confirm that the mounting posts are fully extended and slide the carburetor onto them.
15
Attach the fuel lines to the appropriate ports on the carburetor.
16
Confirm that the O-ring is in place in the air filter housing then reposition the housing by inserting the port into the breather tube as you align the housing on the posts.
17
Replace the support plate then thread and tighten the mounting nuts to secure the assembly.
18
Replace the air filter element.
19
Realign the air filter cover and snap it into place.
Description
This video provides step-by-step instructions for replacing the pump gasket on Honda small engines. The most common reason for replacing the gasket is if it is damaged, causing the engine to run poorly or not start.
All of the information in this gasket replacement video is applicable to the following brands: Honda
Tools used: 8mm socket or nut driver, small flat-head screwdriver, Phillips head screwdriver
All of the information in this gasket replacement video is applicable to the following brands: Honda
Tools used: 8mm socket or nut driver, small flat-head screwdriver, Phillips head screwdriver
Step-By-Step Instructions
1
Before you replace the pump gasket in your engine’s carburetor first make sure the engine has cooled.
2
Now depress the tabs to release the air filter cover and pull out the filter element.
3
Use an 8mm socket or nut driver to unthread the mounting nuts securing the filter housing.
4
Remove the support plate and detach the housing from the breather tube.
5
Note the orientation of the fuel lines attached to the carburetor then detach them – be prepared for some fuel to spill out.
6
With the lines detached, slide the carburetor off of the mounting posts. and set it on a sturdy surface.
7
Use a phillips-head screwdriver to remove the screws holding the carburetor components together.
8
Carefully lift off the needle housing, metering cover and mounting plate assembly.
9
If still intact, separate the old gasket from the pump diaphragm.
10
When installing a new pump gasket we recommend using a new diaphragm as well.
11
Confirm that the spring is in place then align the new gasket on the tabs followed by the diaphragm.
12
Reposition the needle housing, the metering gasket and diaphragm along with the metering cover and mounting plate assembly.
13
Thread and tighten the screws to secure.
14
Confirm that the mounting posts are fully extended and slide the carburetor onto them.
15
Attach the fuel lines to the appropriate ports on the carburetor.
16
Confirm that the O-ring is in place in the air filter housing then reposition the housing by inserting the port into the breather tube as you align the housing on the posts.
17
Replace the support plate then thread and tighten the mounting nuts to secure the assembly.
18
Replace the air filter element.
19
Realign the air filter cover and snap it into place.
Applicable Product Model
Parts Needed
Gasket
$5.92
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com