Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dishwasher Control and Display Board Replacement WD21X10553
GE Dishwasher Control and Display Board Replacement WD21X10553
Skill Level
Total Parts Cost
$86.91Estimated Savings
$112.5009:32
- Description
This video provides step-by-step instructions for replacing the user interface board (control and display board) on GE dishwashers. The main reason for replacing the board is if the user interface no longer lights up or if none of the buttons functions properly.
All of the information in this user interface board replacement video is applicable to the following brands: GE
Tools used: 1/4” socket or nut driver, channel-lock pliers, 5/16” socket or nut driver, small flat-head screwdriver
All of the information in this user interface board replacement video is applicable to the following brands: GE
Tools used: 1/4” socket or nut driver, channel-lock pliers, 5/16” socket or nut driver, small flat-head screwdriver
Step By Step Instructions
1
As with any repair, be sure to turn off the power to your dishwasher before beginning.
2
To replace the user interface board in your dishwasher, you will need to pull the appliance a few inches away from the cabinet in order to fully remove the door.
3
Use a quarter-inch socket or nut driver to remove the screws securing the lower access panel.
4
Remove the panel along with any insulation and determine if the power line and water supply line have enough slack to move the dishwasher.
5
If not you will need to shut off the water supply valve then use channel –lock pliers to help unthread the water supply line fitting from the inlet valve be prepared for some water to spill.
6
Next, use a 5/16th inch socket or nut driver to unthread the screw securing the junction box cover. Then pull the cover off.
7
Note the location of the wires then untwist the wire nuts to disconnect the wires.
8
Unthread the strain relief nut and detach the strain relief from the junction box.
9
Next, disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and remove the mounting bracket screws.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
13
Unhook both door cables from the hinges.
14
Disconnect the door wire connecter and detach the wires from the retainer.
15
Now open the door and lift up to remove it from the hinge supports.
16
Use the quarter-inch socket or nut driver to unthread the two lower screws securing the hinges.
17
Slide the hinges out.
18
Now remove the upper screws securing the inner door panel to the outer panel.
19
Slide the inner panel up to detach it.
20
Disconnect the user interface wire connecters.
21
Remove the four mounting screws securing the user interface board housing to outer housing.
22
Pull the interface board housing free.
23
Use a small flat-head screwdriver to pry off the light bezel.
24
You can now remove the old interface board.
25
Install the new user interface board by setting it in the housing.
26
Realign the light bezel and snap it into place.
27
Reposition the board housing in the outer housing and replace the screws to secure.
28
Realign the tabs on the inner panel with the slots on the outer panel and slide the inner panel down.
29
Replace the screws to secure the two panels.
30
Reposition both door hinges on the support rails and replace the screws to secure.
31
Reinstall the door by aligning the hinge pins in the hinge supports.
32
Close the door then reconnect the door wire connecter and secure the wires in the retainer.
33
Hook both door cables onto the hinges.
34
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
35
Adjust the leveling legs if necessary.
36
Replace the screws to secure the mounting brackets to the cabinet or countertop.
37
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
38
Make sure the hose is elevated above the connection point.
39
Fully position the wire strain relief in the junction box and secure the strain relief nut.
40
Connect the wires using the wire nuts.
41
Align the cover and replace the screw to secure.
42
Reconnect the water supply line to the inlet valve.
43
Replace any insulation then reposition the lower access panel.
44
Secure it with the screws.
45
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing the user interface board (control and display board) on GE dishwashers. The main reason for replacing the board is if the user interface no longer lights up or if none of the buttons functions properly.
All of the information in this user interface board replacement video is applicable to the following brands: GE
Tools used: 1/4” socket or nut driver, channel-lock pliers, 5/16” socket or nut driver, small flat-head screwdriver
All of the information in this user interface board replacement video is applicable to the following brands: GE
Tools used: 1/4” socket or nut driver, channel-lock pliers, 5/16” socket or nut driver, small flat-head screwdriver
Step-By-Step Instructions
1
As with any repair, be sure to turn off the power to your dishwasher before beginning.
2
To replace the user interface board in your dishwasher, you will need to pull the appliance a few inches away from the cabinet in order to fully remove the door.
3
Use a quarter-inch socket or nut driver to remove the screws securing the lower access panel.
4
Remove the panel along with any insulation and determine if the power line and water supply line have enough slack to move the dishwasher.
5
If not you will need to shut off the water supply valve then use channel –lock pliers to help unthread the water supply line fitting from the inlet valve be prepared for some water to spill.
6
Next, use a 5/16th inch socket or nut driver to unthread the screw securing the junction box cover. Then pull the cover off.
7
Note the location of the wires then untwist the wire nuts to disconnect the wires.
8
Unthread the strain relief nut and detach the strain relief from the junction box.
9
Next, disconnect the drain hose from the sink or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and remove the mounting bracket screws.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
13
Unhook both door cables from the hinges.
14
Disconnect the door wire connecter and detach the wires from the retainer.
15
Now open the door and lift up to remove it from the hinge supports.
16
Use the quarter-inch socket or nut driver to unthread the two lower screws securing the hinges.
17
Slide the hinges out.
18
Now remove the upper screws securing the inner door panel to the outer panel.
19
Slide the inner panel up to detach it.
20
Disconnect the user interface wire connecters.
21
Remove the four mounting screws securing the user interface board housing to outer housing.
22
Pull the interface board housing free.
23
Use a small flat-head screwdriver to pry off the light bezel.
24
You can now remove the old interface board.
25
Install the new user interface board by setting it in the housing.
26
Realign the light bezel and snap it into place.
27
Reposition the board housing in the outer housing and replace the screws to secure.
28
Realign the tabs on the inner panel with the slots on the outer panel and slide the inner panel down.
29
Replace the screws to secure the two panels.
30
Reposition both door hinges on the support rails and replace the screws to secure.
31
Reinstall the door by aligning the hinge pins in the hinge supports.
32
Close the door then reconnect the door wire connecter and secure the wires in the retainer.
33
Hook both door cables onto the hinges.
34
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
35
Adjust the leveling legs if necessary.
36
Replace the screws to secure the mounting brackets to the cabinet or countertop.
37
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
38
Make sure the hose is elevated above the connection point.
39
Fully position the wire strain relief in the junction box and secure the strain relief nut.
40
Connect the wires using the wire nuts.
41
Align the cover and replace the screw to secure.
42
Reconnect the water supply line to the inlet valve.
43
Replace any insulation then reposition the lower access panel.
44
Secure it with the screws.
45
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com