Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairMTD Snowblower Engine Recoil Starter Replacement #951-12015
MTD Snowblower Engine Recoil Starter Replacement #951-12015
Skill Level
Total Parts Cost
$114.56Estimated Savings
$112.5003:12
- Description
This video provides step-by-step instructions for replacing the recoil starter on MTD small engines, commonly used in MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, and Yard-Man snowblowers. The most common reason for replacing the recoil starter is if the rope or spring breaks, causing the engine to not start.
All of the information in this recoil starter replacement video is applicable to the following brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Yard-Man
Tools used: 3/8” socket, 5/16” socket
All of the information in this recoil starter replacement video is applicable to the following brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Yard-Man
Tools used: 3/8” socket, 5/16” socket
Step By Step Instructions
1
Before you replace the recoil starter on your snowblower engine, make sure the engine has cooled and the ignition key has been removed.
2
Now, carefully tip the snowblower forward so it rests on the auger housing.
3
Detach the choke lever extension.
4
Next, use a 3/8 inch socket to unthread the three mounting screws securing the lower shroud.
5
Lift the lower shroud off.
6
Next, loosen the rope guide wing nut to release the starter rope and handle.
7
Use a 5/16 inch socket to unthread the mounting screws securing the recoil starter.
8
With the screws and washers removed, set aside the old starter.
9
Install the new recoil starter by aligning it on the blower housing with the washers aligned on the screws.
10
Thread the screws to secure.
11
Extend the starter rope, position it in the rope guide, and tighten the wing nut.
12
Replace the lower shroud by first inserting the tabs into the slots in the frame.
13
Position the shroud and rethread the mounting screws.
14
Replace the choke lever extension with the support tabs facing up.
15
Return the snow blower to its upright position.
16
With the repair completed, reinsert the ignition key, and your snowblower should be ready for use.
Description
This video provides step-by-step instructions for replacing the recoil starter on MTD small engines, commonly used in MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, and Yard-Man snowblowers. The most common reason for replacing the recoil starter is if the rope or spring breaks, causing the engine to not start.
All of the information in this recoil starter replacement video is applicable to the following brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Yard-Man
Tools used: 3/8” socket, 5/16” socket
All of the information in this recoil starter replacement video is applicable to the following brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Yard-Man
Tools used: 3/8” socket, 5/16” socket
Step-By-Step Instructions
1
Before you replace the recoil starter on your snowblower engine, make sure the engine has cooled and the ignition key has been removed.
2
Now, carefully tip the snowblower forward so it rests on the auger housing.
3
Detach the choke lever extension.
4
Next, use a 3/8 inch socket to unthread the three mounting screws securing the lower shroud.
5
Lift the lower shroud off.
6
Next, loosen the rope guide wing nut to release the starter rope and handle.
7
Use a 5/16 inch socket to unthread the mounting screws securing the recoil starter.
8
With the screws and washers removed, set aside the old starter.
9
Install the new recoil starter by aligning it on the blower housing with the washers aligned on the screws.
10
Thread the screws to secure.
11
Extend the starter rope, position it in the rope guide, and tighten the wing nut.
12
Replace the lower shroud by first inserting the tabs into the slots in the frame.
13
Position the shroud and rethread the mounting screws.
14
Replace the choke lever extension with the support tabs facing up.
15
Return the snow blower to its upright position.
16
With the repair completed, reinsert the ignition key, and your snowblower should be ready for use.
Applicable Product Model
Parts Needed
Recoil Starter
$114.56
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com