Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dishwasher Mounting Bracket Replacement #WD35X200
GE Dishwasher Mounting Bracket Replacement #WD35X200
Skill Level
Total Parts Cost
$13.43Estimated Savings
$112.5006:01
- Description
This video provides step-by-step instructions for replacing a mounting bracket on GE dishwashers. The most common reason for replacing a mounting bracket is the dishwasher operating noisily or shaking inside the cabinet.
All of the information in this mounting rack replacement video is applicable to the following brands: GE
All of the information in this mounting rack replacement video is applicable to the following brands: GE
Step By Step Instructions
1
Before you replace or install one or more mounting brackets on your dishwasher be sure to turn off the power to the appliance.
2
To complete the repair, you will need to pull the appliance a few inches away from the cabinet.
3
Use a quarter-inch socket or nut driver to remove the screws securing the lower access panel or panels and remove them.
4
Determine if the power line and water supply line have enough slack to move the dishwasher.
5
If not you will need to shut off the water supply valve then use a 5/8th inch wrench to help unthread the water supply line from the inlet valve be prepared for some water to spill.
6
Next, use a 5/16th inch socket or nut driver to unthread the screw securing the junction box cover. Then pull the cover off.
7
Note the location of the wires then untwist the wire nuts to disconnect the wires.
8
Unthread the strain relief nut and detach the strain relief from the junction box.
9
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and remove the mounting bracket screws if applicable.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
13
If an old mounting bracket is still partially intact you can use a drill with a 1/8th inch drill bit to help break it free.
14
Prepare one or both mounting brackets for installation (sharp)by using a 3/16th inch drill bit to drill two holes through the bracket. we recommend securing the bracket with locking pliers.
15
If required, use a 3/32nd inch drill bit to drill the accompanying holes in the metal frame – be careful not to drill through the tub.
16
Now align the bracket and secure it with the provided screws.
17
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
18
Adjust the leveling legs if necessary.
19
Replace the screws to secure the mounting brackets to the cabinet or countertop.
20
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
21
Make sure the hose is elevated above the connection point.
22
Fully position the wire strain relief in the junction box and secure the strain relief nut.
23
Connect the wires using the wire nuts.
24
Align the cover and replace the screw to secure.
25
Reconnect the water supply line to the inlet valve.
26
Reposition the lower access panel or panels and replace the screws to secure.
27
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step instructions for replacing a mounting bracket on GE dishwashers. The most common reason for replacing a mounting bracket is the dishwasher operating noisily or shaking inside the cabinet.
All of the information in this mounting rack replacement video is applicable to the following brands: GE
All of the information in this mounting rack replacement video is applicable to the following brands: GE
Step-By-Step Instructions
1
Before you replace or install one or more mounting brackets on your dishwasher be sure to turn off the power to the appliance.
2
To complete the repair, you will need to pull the appliance a few inches away from the cabinet.
3
Use a quarter-inch socket or nut driver to remove the screws securing the lower access panel or panels and remove them.
4
Determine if the power line and water supply line have enough slack to move the dishwasher.
5
If not you will need to shut off the water supply valve then use a 5/8th inch wrench to help unthread the water supply line from the inlet valve be prepared for some water to spill.
6
Next, use a 5/16th inch socket or nut driver to unthread the screw securing the junction box cover. Then pull the cover off.
7
Note the location of the wires then untwist the wire nuts to disconnect the wires.
8
Unthread the strain relief nut and detach the strain relief from the junction box.
9
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and remove the mounting bracket screws if applicable.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
13
If an old mounting bracket is still partially intact you can use a drill with a 1/8th inch drill bit to help break it free.
14
Prepare one or both mounting brackets for installation (sharp)by using a 3/16th inch drill bit to drill two holes through the bracket. we recommend securing the bracket with locking pliers.
15
If required, use a 3/32nd inch drill bit to drill the accompanying holes in the metal frame – be careful not to drill through the tub.
16
Now align the bracket and secure it with the provided screws.
17
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
18
Adjust the leveling legs if necessary.
19
Replace the screws to secure the mounting brackets to the cabinet or countertop.
20
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
21
Make sure the hose is elevated above the connection point.
22
Fully position the wire strain relief in the junction box and secure the strain relief nut.
23
Connect the wires using the wire nuts.
24
Align the cover and replace the screw to secure.
25
Reconnect the water supply line to the inlet valve.
26
Reposition the lower access panel or panels and replace the screws to secure.
27
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com