Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairDuet/ HE3 Dryer Thermal Fuse Replacement Part # WP3392519
Duet/ HE3 Dryer Thermal Fuse Replacement Part # WP3392519
Skill Level
Total Parts Cost
$19.49Estimated Savings
$112.5004:30
- Description
This video provides step-by-step repair instructions for replacing the thermal fuse on a Whirlpool/ Kenmore Duet/ HE3 dryer. The two most common reasons for replacing the thermal fuse are when the dryer doesn't heat or won’t start.
All of the information for this thermal fuse replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Crosley, Inglis, Amana, Admiral
Tools needed: hex socket, flat head screwdriver, Phillips head screwdriver, putty knife
All of the information for this thermal fuse replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Crosley, Inglis, Amana, Admiral
Tools needed: hex socket, flat head screwdriver, Phillips head screwdriver, putty knife
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the top panel screws and set the panel aside.
3
Next, depress the tabs on the control panel and pull it off.
4
Disconnect the wire harness.
5
Remove the screws to release the circuit board bracket.
6
Remove the control bracket screws and detach the bracket.
7
Now, remove the screws located at the base of the dryer.
8
Pull the lower panel out and then down to detach.
9
Reach into the lower cabinet to disconnect the door switch and moisture sensor wire harnesses.
10
Remove the screws at the bottom and at the top of the front panel.
11
Remove the mounting screws located inside the door to release the front panel.
12
Remove the lower bulkhead mounting screws and loosen the upper screws.
13
Remove the mounting screws from the blower housing.
14
Lift the bulkhead off the upper mounting screws and set it aside.
15
Now use the belt to lift out the drum.
16
Disconnect the wires to the old fuse remove the mounting screw and pull the old fuse out.
17
Install the new thermal fuse by sliding it into the slot then secure the mounting screw and reconnect the wires.
18
Now, replace the drum by aligning its rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a “zig-zag” formation.
19
Rotate the drum to help align the belt.
20
Now, reinstall the bulkhead by aligning it on the upper screws.
21
Tighten these screws then replace the lower screws as well as the blower housing screws.
22
Reattach the front panel by lining it up on the cabinet then, secure it with the upper and lower screws as well as the screws inside the door.
23
Reconnect the door switch and moisture sensor wire harnesses.
24
Slide the lower panel up into position and secure it with the screws.
25
Reinstall the control panel bracket.
26
Reattach the circuit board bracket.
27
Reconnect the control panel’s wire harness and snap the panel back into place.
28
Replace the top panel secure it with the screws. and plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step repair instructions for replacing the thermal fuse on a Whirlpool/ Kenmore Duet/ HE3 dryer. The two most common reasons for replacing the thermal fuse are when the dryer doesn't heat or won’t start.
All of the information for this thermal fuse replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Crosley, Inglis, Amana, Admiral
Tools needed: hex socket, flat head screwdriver, Phillips head screwdriver, putty knife
All of the information for this thermal fuse replacement video is applicable to the following brands:
Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Crosley, Inglis, Amana, Admiral
Tools needed: hex socket, flat head screwdriver, Phillips head screwdriver, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the top panel screws and set the panel aside.
3
Next, depress the tabs on the control panel and pull it off.
4
Disconnect the wire harness.
5
Remove the screws to release the circuit board bracket.
6
Remove the control bracket screws and detach the bracket.
7
Now, remove the screws located at the base of the dryer.
8
Pull the lower panel out and then down to detach.
9
Reach into the lower cabinet to disconnect the door switch and moisture sensor wire harnesses.
10
Remove the screws at the bottom and at the top of the front panel.
11
Remove the mounting screws located inside the door to release the front panel.
12
Remove the lower bulkhead mounting screws and loosen the upper screws.
13
Remove the mounting screws from the blower housing.
14
Lift the bulkhead off the upper mounting screws and set it aside.
15
Now use the belt to lift out the drum.
16
Disconnect the wires to the old fuse remove the mounting screw and pull the old fuse out.
17
Install the new thermal fuse by sliding it into the slot then secure the mounting screw and reconnect the wires.
18
Now, replace the drum by aligning its rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a “zig-zag” formation.
19
Rotate the drum to help align the belt.
20
Now, reinstall the bulkhead by aligning it on the upper screws.
21
Tighten these screws then replace the lower screws as well as the blower housing screws.
22
Reattach the front panel by lining it up on the cabinet then, secure it with the upper and lower screws as well as the screws inside the door.
23
Reconnect the door switch and moisture sensor wire harnesses.
24
Slide the lower panel up into position and secure it with the screws.
25
Reinstall the control panel bracket.
26
Reattach the circuit board bracket.
27
Reconnect the control panel’s wire harness and snap the panel back into place.
28
Replace the top panel secure it with the screws. and plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Thermal Fuse
$19.49
Total$0.00
Related Articles & Videos
01:12
Part Replacement
Dryer Not Heating? – Whirlpool/Kenmore Dryer Repair Part # 3392519
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com