Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairRoller Assembly Replacement – Electrolux Electric Dryer #134715900
Roller Assembly Replacement – Electrolux Electric Dryer #134715900
Skill Level
Total Parts Cost
$77.75Estimated Savings
$112.5012:02
- Description
This video provides step-by-step instructions for replacing the roller assembly on Electrolux electric dryers. The most common reason for replacing the roller is if the dryer is noisy or wobbling.
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, 1/4 inch allen wrench, 14 mm wrench, pliers, quarter inch socket
All of the information in this roller assembly replacement video is applicable to the following brands: Electrolux
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, 1/4 inch allen wrench, 14 mm wrench, pliers, quarter inch socket
All of the information in this roller assembly replacement video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Before you replace a roller assembly in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel mounting brackets to the frame.
5
With the screws removed, lift the panel up and use a small flat-head screwdriver to depress the retaining tab to release the wire connecter.
6
Open the dryer door and unthread the two screws on the front panel securing the lint filter housing cover.
7
Lift and support the dryer then unthread the bottom front panel mounting screws.
8
With the screws unthreaded, remove the support and unthread the top front panel mounting screws.
9
Lift the panel up and out.
10
Disconnect the door switch wire connecter to fully remove the front panel.
11
Now disconnect both the drum light wire connecter and the user control board wire connecter from the main control board.
12
Next, unthread the control board support bracket screws and detach the bracket from the front bulkhead.
13
Unthread the lower bulkhead mounting screws.
14
Carefully lift the front bulkhead up to detach it from the frame.
15
If you’re replacing a front roller assembly use a quarter-inch Allen wrench to secure the roller as you use a 14mm wrench to unthread the mounting nut.
16
Remove the old roller assembly.
17
Install the new roller assembly by sliding a washer onto the roller shaft.
18
Insert the shaft into the bulkhead.
19
Slide on the second washer then thread the mounting nut and tighten.
20
If you’re replacing a rear roller assembly support the main control board bracket.
21
Reach under the drum and unthread the belt from the pulley and motor shaft.
22
You can use the belt to help lift out the drum.
23
Next, remove the screws to release the main top mounting bracket.
24
Close the water supply valve and remove the water supply line from the inlet valve – be prepared for some water to spill.
25
Now remove the screw to release the rear access panel.
26
Note the orientation of the power cord wires on the terminal block then use a quarter-inch socket or a phillips-head screwdriver to unthread the screws to disconnect the wires.
27
Now remove all of the screws securing the rear panel.
28
Set the rear panel aside.
29
You can now secure the roller you’re replacing and unthread the mounting nut to release the assembly.
30
Install the new roller assembly in the same manner as shown before.
31
With the roller in place, reposition the rear panel then thread and tighten the screws to secure.
32
Note that the longer screw should be used to secure the panel above the exhaust vent.
33
Connect the power cord wires to the appropriate terminals on the terminal block and secure them with the screws.
34
Replace the rear access panel and secure it with the screw.
35
Attach the water supply line to the inlet valve.
36
Reopen the water supply valve.
37
Realign the main top mounting bracket and replace the screws to secure.
38
Reinstall the drum by positioning it on the rear rollers.
39
Loop the belt on the pulley and motor shaft in a zig-zag formation.
40
Rotate the drum to help align the belt.
41
Reinstall the front bulkhead by inserting the tabs into the slots in the frame as you align the drum on the front rollers.
42
Thread and tighten the lower bulkhead mounting screws.
43
Detach the support from the main control board bracket and hook the bracket onto the bulkhead.
44
Replace the screws.
45
Reconnect the user control board wire connecter as well as the drum light wire connecter.
46
Reinstall the front panel by first reconnecting the door switch wire connecter.
47
Now hook the front panel tabs on the slots in the frame.
48
Replace the panel mounting screws on top.
49
Lift and support the dryer to replace the bottom mounting screws.
50
Thread and tighten the two screws to secure the lint filter housing cover to the front panel.
51
Connect the wire connecter to the user control board.
52
Reposition the control panel and replace the screws to secure the brackets.
53
Realign the main top and slide it into place.
54
Rethread the screws in the back.
55
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the roller assembly on Electrolux electric dryers. The most common reason for replacing the roller is if the dryer is noisy or wobbling.
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, 1/4 inch allen wrench, 14 mm wrench, pliers, quarter inch socket
All of the information in this roller assembly replacement video is applicable to the following brands: Electrolux
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, 1/4 inch allen wrench, 14 mm wrench, pliers, quarter inch socket
All of the information in this roller assembly replacement video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Before you replace a roller assembly in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel mounting brackets to the frame.
5
With the screws removed, lift the panel up and use a small flat-head screwdriver to depress the retaining tab to release the wire connecter.
6
Open the dryer door and unthread the two screws on the front panel securing the lint filter housing cover.
7
Lift and support the dryer then unthread the bottom front panel mounting screws.
8
With the screws unthreaded, remove the support and unthread the top front panel mounting screws.
9
Lift the panel up and out.
10
Disconnect the door switch wire connecter to fully remove the front panel.
11
Now disconnect both the drum light wire connecter and the user control board wire connecter from the main control board.
12
Next, unthread the control board support bracket screws and detach the bracket from the front bulkhead.
13
Unthread the lower bulkhead mounting screws.
14
Carefully lift the front bulkhead up to detach it from the frame.
15
If you’re replacing a front roller assembly use a quarter-inch Allen wrench to secure the roller as you use a 14mm wrench to unthread the mounting nut.
16
Remove the old roller assembly.
17
Install the new roller assembly by sliding a washer onto the roller shaft.
18
Insert the shaft into the bulkhead.
19
Slide on the second washer then thread the mounting nut and tighten.
20
If you’re replacing a rear roller assembly support the main control board bracket.
21
Reach under the drum and unthread the belt from the pulley and motor shaft.
22
You can use the belt to help lift out the drum.
23
Next, remove the screws to release the main top mounting bracket.
24
Close the water supply valve and remove the water supply line from the inlet valve – be prepared for some water to spill.
25
Now remove the screw to release the rear access panel.
26
Note the orientation of the power cord wires on the terminal block then use a quarter-inch socket or a phillips-head screwdriver to unthread the screws to disconnect the wires.
27
Now remove all of the screws securing the rear panel.
28
Set the rear panel aside.
29
You can now secure the roller you’re replacing and unthread the mounting nut to release the assembly.
30
Install the new roller assembly in the same manner as shown before.
31
With the roller in place, reposition the rear panel then thread and tighten the screws to secure.
32
Note that the longer screw should be used to secure the panel above the exhaust vent.
33
Connect the power cord wires to the appropriate terminals on the terminal block and secure them with the screws.
34
Replace the rear access panel and secure it with the screw.
35
Attach the water supply line to the inlet valve.
36
Reopen the water supply valve.
37
Realign the main top mounting bracket and replace the screws to secure.
38
Reinstall the drum by positioning it on the rear rollers.
39
Loop the belt on the pulley and motor shaft in a zig-zag formation.
40
Rotate the drum to help align the belt.
41
Reinstall the front bulkhead by inserting the tabs into the slots in the frame as you align the drum on the front rollers.
42
Thread and tighten the lower bulkhead mounting screws.
43
Detach the support from the main control board bracket and hook the bracket onto the bulkhead.
44
Replace the screws.
45
Reconnect the user control board wire connecter as well as the drum light wire connecter.
46
Reinstall the front panel by first reconnecting the door switch wire connecter.
47
Now hook the front panel tabs on the slots in the frame.
48
Replace the panel mounting screws on top.
49
Lift and support the dryer to replace the bottom mounting screws.
50
Thread and tighten the two screws to secure the lint filter housing cover to the front panel.
51
Connect the wire connecter to the user control board.
52
Reposition the control panel and replace the screws to secure the brackets.
53
Realign the main top and slide it into place.
54
Rethread the screws in the back.
55
With the repair completed plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Parts Needed
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com