Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Electric Dryer Terminal Block Replacement 137150200
Electrolux Electric Dryer Terminal Block Replacement 137150200
Skill Level
Total Parts Cost
$44.78Estimated Savings
$112.5003:59
- Description
This video provides step-by-step instructions for replacing the terminal block on Electrolux electric dryers. The most common reason for replacing the terminal block is if the dryer will not turn on.
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, quarter inch socket, wire cutter, wire stripper
All of the information in this terminal block replacement video is applicable to the following brands: Electrolux
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, quarter inch socket, wire cutter, wire stripper
All of the information in this terminal block replacement video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Before you replace the terminal block in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screw to release the rear access panel.
3
Note the orientation of the power cord wires on the terminal block then use a quarter-inch socket or the phillips-head screwdriver to unthread the screws to disconnect the wires.
4
Use the number two square bit or phillips-head to unthread the terminal block mounting screw.
5
Unhook the old terminal block.
6
Note the orientation of the power supply wires then use wire cutters to cut the wires as close to the terminals as possible.
7
Before you install the new terminal block strip off a quarter-inch of insulation from the wires.
8
Attach the wires to the provided terminals and crimp to secure.
9
Make sure the white neutral wire is attached to the silver terminal.
10
Now align the terminals in the new terminal block and snap them into place – align the silver terminal in the middle.
11
Insert the terminal block tabs into the slots in the bulkhead and replace the mounting screw.
12
Now align the power cord wires on the appropriate terminals then thread the screws and tighten to secure.
13
Replace the rear access panel and secure it with the screw.
14
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the terminal block on Electrolux electric dryers. The most common reason for replacing the terminal block is if the dryer will not turn on.
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, quarter inch socket, wire cutter, wire stripper
All of the information in this terminal block replacement video is applicable to the following brands: Electrolux
Parts used: #2 square bit, phillips head screwdriver, flat head screwdriver, quarter inch socket, wire cutter, wire stripper
All of the information in this terminal block replacement video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Before you replace the terminal block in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screw to release the rear access panel.
3
Note the orientation of the power cord wires on the terminal block then use a quarter-inch socket or the phillips-head screwdriver to unthread the screws to disconnect the wires.
4
Use the number two square bit or phillips-head to unthread the terminal block mounting screw.
5
Unhook the old terminal block.
6
Note the orientation of the power supply wires then use wire cutters to cut the wires as close to the terminals as possible.
7
Before you install the new terminal block strip off a quarter-inch of insulation from the wires.
8
Attach the wires to the provided terminals and crimp to secure.
9
Make sure the white neutral wire is attached to the silver terminal.
10
Now align the terminals in the new terminal block and snap them into place – align the silver terminal in the middle.
11
Insert the terminal block tabs into the slots in the bulkhead and replace the mounting screw.
12
Now align the power cord wires on the appropriate terminals then thread the screws and tighten to secure.
13
Replace the rear access panel and secure it with the screw.
14
With the repair completed plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Parts Needed
Terminal Block
$44.78
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com