Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Electric Dryer Drum Light Assembly #137526000
Electrolux Electric Dryer Drum Light Assembly #137526000
Skill Level
Total Parts Cost
$138.27Estimated Savings
$112.5005:18
- Description
This video provides step-by-step instructions for replacing the drum light assembly on Electrolux electric dryers. The most common reason for replacing the drum light is if it will not turn on.
Parts used: #2 square bit, Phillips head screwdriver, flat head screwdriver
All of the information in this drum light replacement video is applicable to the following brands: Electrolux
Parts used: #2 square bit, Phillips head screwdriver, flat head screwdriver
All of the information in this drum light replacement video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Before you replace the led drum light assembly in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel mounting brackets to the frame.
5
With the screws removed, lift the panel up and use a small flat-head screwdriver to depress the retaining tab to release the wire connecter.
6
Open the dryer door and unthread the two screws on the front panel securing the lint filter housing cover.
7
Lift and support the dryer then unthread the bottom front panel mounting screws.
8
With the screws unthreaded, remove the support and unthread the top front panel mounting screws.
9
Lift the panel up and out.
10
Disconnect the door switch wire connecter to fully remove the front panel.
11
Now disconnect the drum light wire connecter.
12
Cut the zip tie securing the wires.
13
Rotate the drum light assembly counter-clockwise to release it from the bulkhead.
14
Install the new led drum light assembly by first feeding the wire through the hole in the bulkhead.
15
Now position the light assembly and rotate it clockwise to lock it into place.
16
Connect the wire connecter to the main control board.
17
Use a zip tie to secure the wires.
18
Reinstall the front panel by first reconnecting the door switch wire connecter.
19
Now hook the front panel tabs on the slots in the frame.
20
Replace the panel mounting screws on top.
21
Lift and support the dryer to replace the bottom mounting screws.
22
Thread and tighten the two screws to secure the lint filter housing cover to the front panel.
23
Connect the wire connecter to the user control board.
24
Reposition the control panel and replace the screws to secure the brackets.
25
Realign the main top and slide it into place.
26
Rethread the screws in the back.
27
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the drum light assembly on Electrolux electric dryers. The most common reason for replacing the drum light is if it will not turn on.
Parts used: #2 square bit, Phillips head screwdriver, flat head screwdriver
All of the information in this drum light replacement video is applicable to the following brands: Electrolux
Parts used: #2 square bit, Phillips head screwdriver, flat head screwdriver
All of the information in this drum light replacement video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Before you replace the led drum light assembly in your dryer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel mounting brackets to the frame.
5
With the screws removed, lift the panel up and use a small flat-head screwdriver to depress the retaining tab to release the wire connecter.
6
Open the dryer door and unthread the two screws on the front panel securing the lint filter housing cover.
7
Lift and support the dryer then unthread the bottom front panel mounting screws.
8
With the screws unthreaded, remove the support and unthread the top front panel mounting screws.
9
Lift the panel up and out.
10
Disconnect the door switch wire connecter to fully remove the front panel.
11
Now disconnect the drum light wire connecter.
12
Cut the zip tie securing the wires.
13
Rotate the drum light assembly counter-clockwise to release it from the bulkhead.
14
Install the new led drum light assembly by first feeding the wire through the hole in the bulkhead.
15
Now position the light assembly and rotate it clockwise to lock it into place.
16
Connect the wire connecter to the main control board.
17
Use a zip tie to secure the wires.
18
Reinstall the front panel by first reconnecting the door switch wire connecter.
19
Now hook the front panel tabs on the slots in the frame.
20
Replace the panel mounting screws on top.
21
Lift and support the dryer to replace the bottom mounting screws.
22
Thread and tighten the two screws to secure the lint filter housing cover to the front panel.
23
Connect the wire connecter to the user control board.
24
Reposition the control panel and replace the screws to secure the brackets.
25
Realign the main top and slide it into place.
26
Rethread the screws in the back.
27
With the repair completed plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com