Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairHonda Lawn Mower Right Rear Wheel Plate Part # 42990-VL0-900
Honda Lawn Mower Right Rear Wheel Plate Part # 42990-VL0-900
Skill Level
Total Parts Cost
$21.92Estimated Savings
$112.5005:25
- Description
This video provides step-by-step repair instructions for replacing the wheel plate on a Honda lawn mower. The most common reason for replacing the wheel plate is when it is damaged.
All of the information for this wheel plate replacement video is applicable to the following brands:
Honda
Tools needed: 12mm socket, snap wring pliers, 12mm wrench
All of the information for this wheel plate replacement video is applicable to the following brands:
Honda
Tools needed: 12mm socket, snap wring pliers, 12mm wrench
Step By Step Instructions
1
Before you replace the right rear wheel adjustment plate on your lawn mower first make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting and close the fuel valve.
3
We recommend performing this procedure with little or no fuel in the tank and draining the oil as well.
4
Now lift up the rear of the mower and support it.
5
Use a 12mm socket to unthread the bolt securing the right rear wheel and remove the wheel.
6
Use snap ring pliers to remove the snap ring securing the pinion gear.
7
Remove the washer then note the orientation of the pinion gear and slide it off.
8
Remove the dust cover and slide off the small spacer washer.
9
Release the snap ring securing the large spacer washer and remove it along with the flat washer.
10
Now carefully tip the mower on its side.
11
Release the large snap ring securing the wheel support assembly and slide off the assembly.
12
Lift up the rear deflector and secure it.
13
You can now use a 12mm socket to unthread the mounting nuts securing the adjustment plate.
14
Remove the old plate.
15
Install the new adjustment plate by positioning it on the frame.
16
Thread and tighten the mounting nuts to secure.
17
Confirm that the adjuster arm is positioned on the support with the tab facing up.
18
Position the wheel support assembly on the axle with the adjuster arm disengaged from the plate.
19
Slide the washer up and secure the large snap ring.
20
Return the adjuster arm to the desired position.
21
Release the rear deflector return the mower to its upright position and support it.
22
Make sure the axle is fully extended through the support.
23
Slide on the large spacer washer followed by the flat washer.
24
Replace the snap ring and slide on the small spacer washer.
25
Replace the dust cover.
26
Confirm that the ratchet return spring is intact in the axle then insert the ratchet key.
27
Hold the key in place as you properly align the pinion gear.
28
Slide on the washer and secure the assembly with the snap ring.
29
Insert the mounting bolt through the wheel and slide on the wave washer with the curved edge facing outward followed by the flat washer.
30
Position the dust cover align the wheel assembly then thread and tighten the mounting bolt to secure.
31
With the repair completed reattach the wire and boot to the spark plug open the fuel valve refill the fuel tank replace the oil and your lawn mower should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the wheel plate on a Honda lawn mower. The most common reason for replacing the wheel plate is when it is damaged.
All of the information for this wheel plate replacement video is applicable to the following brands:
Honda
Tools needed: 12mm socket, snap wring pliers, 12mm wrench
All of the information for this wheel plate replacement video is applicable to the following brands:
Honda
Tools needed: 12mm socket, snap wring pliers, 12mm wrench
Step-By-Step Instructions
1
Before you replace the right rear wheel adjustment plate on your lawn mower first make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting and close the fuel valve.
3
We recommend performing this procedure with little or no fuel in the tank and draining the oil as well.
4
Now lift up the rear of the mower and support it.
5
Use a 12mm socket to unthread the bolt securing the right rear wheel and remove the wheel.
6
Use snap ring pliers to remove the snap ring securing the pinion gear.
7
Remove the washer then note the orientation of the pinion gear and slide it off.
8
Remove the dust cover and slide off the small spacer washer.
9
Release the snap ring securing the large spacer washer and remove it along with the flat washer.
10
Now carefully tip the mower on its side.
11
Release the large snap ring securing the wheel support assembly and slide off the assembly.
12
Lift up the rear deflector and secure it.
13
You can now use a 12mm socket to unthread the mounting nuts securing the adjustment plate.
14
Remove the old plate.
15
Install the new adjustment plate by positioning it on the frame.
16
Thread and tighten the mounting nuts to secure.
17
Confirm that the adjuster arm is positioned on the support with the tab facing up.
18
Position the wheel support assembly on the axle with the adjuster arm disengaged from the plate.
19
Slide the washer up and secure the large snap ring.
20
Return the adjuster arm to the desired position.
21
Release the rear deflector return the mower to its upright position and support it.
22
Make sure the axle is fully extended through the support.
23
Slide on the large spacer washer followed by the flat washer.
24
Replace the snap ring and slide on the small spacer washer.
25
Replace the dust cover.
26
Confirm that the ratchet return spring is intact in the axle then insert the ratchet key.
27
Hold the key in place as you properly align the pinion gear.
28
Slide on the washer and secure the assembly with the snap ring.
29
Insert the mounting bolt through the wheel and slide on the wave washer with the curved edge facing outward followed by the flat washer.
30
Position the dust cover align the wheel assembly then thread and tighten the mounting bolt to secure.
31
With the repair completed reattach the wire and boot to the spark plug open the fuel valve refill the fuel tank replace the oil and your lawn mower should be ready for use.
Applicable Product Model
Total$0.00
Related Articles & Videos
04:36
Part Replacement
Honda Lawn Mower Replace Left Rear Wheel Support Part # 42940-VG3-B01
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com