Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLennox Furnace Blower Motor Replacement #60L22
Lennox Furnace Blower Motor Replacement #60L22
Skill Level
Total Parts Cost
$492.00Estimated Savings
$112.5007:01
- Description
This video provides step-by-step instructions for replacing the circulation blower motor on Lennox furnaces. The most common reasons for replacing the circulation blower motor are when the furnace is loud or the blower does not run.
All of the information in this blower motor replacement video is applicable to the following brands: Lennox
Tools needed: 1/4 inch socket, adjustable wrench, 5/16 inch socket, 3/8 inch socket
Connect With Us!
All of the information in this blower motor replacement video is applicable to the following brands: Lennox
Tools needed: 1/4 inch socket, adjustable wrench, 5/16 inch socket, 3/8 inch socket
Connect With Us!
Step By Step Instructions
1
Before you replace the blower motor in your furnace first turn off the power to the furnace.
2
Unthread the retaining knobs securing the upper access panel and remove the panel.
3
Use a quarter-inch socket or nut driver to unthread the mounting screws securing the lower access panel.
4
Lift the panel up to remove.
5
To ensure the run capacitor is discharged, place a screwdriver with an insulated handle across the terminals – avoid touching the screwdriver blade.
6
Now disconnect the wires from the capacitor terminals.
7
If necessary, note the orientation of the thermostat wires then disconnect them from the control board to move them out of the way.
8
Note the orientation of the blower motor wires then disconnect them from the board.
9
Cut the zip tie securing the control board wires.
10
Next, use the quarter inch socket or nut driver to loosen the screws securing the control board mounting panel.
11
Slide the panel forward to detach and move it out of the way.
12
Note where the blower assembly mounting rails are positioned on the support then use a 5/16th inch socket or nut driver to unthread the screws securing the rails.
13
With the screws removed, carefully slide out the blower assembly.
14
Use an adjustable wrench to loosen the set screw to release the blower wheel from the motor shaft.
15
Now tip the assembly on its side with the motor facing up.
16
Remove the screw to detach the grounding wire.
17
Cut the zip tie securing the motor wires.
18
Now use a 3/8th inch socket to unthread the blower motor mounting bolts.
19
Note the orientation of the old motor then lift it off of the blower housing.
20
Install the new blower motor by inserting the shaft into the blower wheel as you properly align the motor on the housing.
21
Confirm that the shoulder washers are intact on the motor mounting brackets then thread and tighten the bolts to secure the motor.
22
Use a zip tie to secure the motor wires.
23
Make sure the grounding wire is secured with the screw.
24
Now return the blower assembly to its upright position.
25
With the flat side of the motor shaft facing the set screw center the blower wheel in the housing and tighten the set screw.
26
Realign the blower assembly mounting rails with the slots on the support and slide the assembly into position.
27
Replace the screws to secure the rails.
28
Reposition the control board panel on the support and tighten the screws to secure.
29
Attach the blower motor wires to the appropriate terminals on the control board.
30
Connect the capacitor wires.
31
If applicable, reconnect the thermostat wires as well.
32
Use a zip tie to secure the control board wires.
33
Replace the lower access panel by aligning the bottom edge first.
34
Thread and tighten the screws to secure.
35
Realign the top edge of the upper access panel then thread the retaining knobs to secure.
36
With the repair completed
37
Turn the power back on and your furnace should be ready for use.
Description
This video provides step-by-step instructions for replacing the circulation blower motor on Lennox furnaces. The most common reasons for replacing the circulation blower motor are when the furnace is loud or the blower does not run.
All of the information in this blower motor replacement video is applicable to the following brands: Lennox
Tools needed: 1/4 inch socket, adjustable wrench, 5/16 inch socket, 3/8 inch socket
Connect With Us!
All of the information in this blower motor replacement video is applicable to the following brands: Lennox
Tools needed: 1/4 inch socket, adjustable wrench, 5/16 inch socket, 3/8 inch socket
Connect With Us!
Step-By-Step Instructions
1
Before you replace the blower motor in your furnace first turn off the power to the furnace.
2
Unthread the retaining knobs securing the upper access panel and remove the panel.
3
Use a quarter-inch socket or nut driver to unthread the mounting screws securing the lower access panel.
4
Lift the panel up to remove.
5
To ensure the run capacitor is discharged, place a screwdriver with an insulated handle across the terminals – avoid touching the screwdriver blade.
6
Now disconnect the wires from the capacitor terminals.
7
If necessary, note the orientation of the thermostat wires then disconnect them from the control board to move them out of the way.
8
Note the orientation of the blower motor wires then disconnect them from the board.
9
Cut the zip tie securing the control board wires.
10
Next, use the quarter inch socket or nut driver to loosen the screws securing the control board mounting panel.
11
Slide the panel forward to detach and move it out of the way.
12
Note where the blower assembly mounting rails are positioned on the support then use a 5/16th inch socket or nut driver to unthread the screws securing the rails.
13
With the screws removed, carefully slide out the blower assembly.
14
Use an adjustable wrench to loosen the set screw to release the blower wheel from the motor shaft.
15
Now tip the assembly on its side with the motor facing up.
16
Remove the screw to detach the grounding wire.
17
Cut the zip tie securing the motor wires.
18
Now use a 3/8th inch socket to unthread the blower motor mounting bolts.
19
Note the orientation of the old motor then lift it off of the blower housing.
20
Install the new blower motor by inserting the shaft into the blower wheel as you properly align the motor on the housing.
21
Confirm that the shoulder washers are intact on the motor mounting brackets then thread and tighten the bolts to secure the motor.
22
Use a zip tie to secure the motor wires.
23
Make sure the grounding wire is secured with the screw.
24
Now return the blower assembly to its upright position.
25
With the flat side of the motor shaft facing the set screw center the blower wheel in the housing and tighten the set screw.
26
Realign the blower assembly mounting rails with the slots on the support and slide the assembly into position.
27
Replace the screws to secure the rails.
28
Reposition the control board panel on the support and tighten the screws to secure.
29
Attach the blower motor wires to the appropriate terminals on the control board.
30
Connect the capacitor wires.
31
If applicable, reconnect the thermostat wires as well.
32
Use a zip tie to secure the control board wires.
33
Replace the lower access panel by aligning the bottom edge first.
34
Thread and tighten the screws to secure.
35
Realign the top edge of the upper access panel then thread the retaining knobs to secure.
36
With the repair completed
37
Turn the power back on and your furnace should be ready for use.
Applicable Product Model
Parts Needed
Blower Motor
$492.00
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com