Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Dryer Replace Gas Valve Solenoid Kit #5303931775
Frigidaire Dryer Replace Gas Valve Solenoid Kit #5303931775
Skill Level
Total Parts Cost
$27.74Estimated Savings
$112.5002:32
- Description
This video provides step-by-step repair instructions for replacing the gas valve solenoid coil kit on a Frigidaire dryer. The most common reasons for replacing the gas valve solenoids are when the dryer doesn’t heat, takes too long, or won’t stop.
All of the information for this gas valve solenoid replacement video is applicable to the following brands:
Frigidaire, Westinghouse, Kenmore, Gibson, Montgomery Wards, Universal, Kelvinator, Tappan, Electrolux, Crosley
Tools needed: putty knife, screwdriver
All of the information for this gas valve solenoid replacement video is applicable to the following brands:
Frigidaire, Westinghouse, Kenmore, Gibson, Montgomery Wards, Universal, Kelvinator, Tappan, Electrolux, Crosley
Tools needed: putty knife, screwdriver
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to insert a putty knife under the front of the main top to release the spring clips.
3
Now rotate the top up and support it.
4
If you dryer has a rear control panel
5
You next step is to disconnect the door switch wires.
6
If your dryer has the control panel in the front you will need to disconnect the wire harness.
7
If necessary, you may also need to remove the zip tie securing the wires.
8
Now, remove the front panel mounting screws and pull the front panel up and out to remove.
9
Disconnect the wire harnesses from the old solenoid coils.
10
Remove the screws to release the bracket and pull the old coils off of the gas valve.
11
Install the new solenoid coils by sliding them onto the gas valve shafts.
12
Align the bracket and secure the screws.
13
Reconnect the wire harnesses.
14
Reinstall the front panel by aligning the slots at the bottom of the panel with the support clips then lift up the drum as you snap the front panel into place.
15
Secure the mounting screws and reconnect the wire harness or door switch wires depending on your model.
16
Use a zip tie to secure the wires.
17
Rotate the main top back into place and press down on the front to secure the spring clips.
18
You’re now ready to turn the gas supply back on and plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step repair instructions for replacing the gas valve solenoid coil kit on a Frigidaire dryer. The most common reasons for replacing the gas valve solenoids are when the dryer doesn’t heat, takes too long, or won’t stop.
All of the information for this gas valve solenoid replacement video is applicable to the following brands:
Frigidaire, Westinghouse, Kenmore, Gibson, Montgomery Wards, Universal, Kelvinator, Tappan, Electrolux, Crosley
Tools needed: putty knife, screwdriver
All of the information for this gas valve solenoid replacement video is applicable to the following brands:
Frigidaire, Westinghouse, Kenmore, Gibson, Montgomery Wards, Universal, Kelvinator, Tappan, Electrolux, Crosley
Tools needed: putty knife, screwdriver
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to insert a putty knife under the front of the main top to release the spring clips.
3
Now rotate the top up and support it.
4
If you dryer has a rear control panel
5
You next step is to disconnect the door switch wires.
6
If your dryer has the control panel in the front you will need to disconnect the wire harness.
7
If necessary, you may also need to remove the zip tie securing the wires.
8
Now, remove the front panel mounting screws and pull the front panel up and out to remove.
9
Disconnect the wire harnesses from the old solenoid coils.
10
Remove the screws to release the bracket and pull the old coils off of the gas valve.
11
Install the new solenoid coils by sliding them onto the gas valve shafts.
12
Align the bracket and secure the screws.
13
Reconnect the wire harnesses.
14
Reinstall the front panel by aligning the slots at the bottom of the panel with the support clips then lift up the drum as you snap the front panel into place.
15
Secure the mounting screws and reconnect the wire harness or door switch wires depending on your model.
16
Use a zip tie to secure the wires.
17
Rotate the main top back into place and press down on the front to secure the spring clips.
18
You’re now ready to turn the gas supply back on and plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Gas Valve Solenoid
$27.74
Total$0.00
Related Articles & Videos
04:26
Part Replacement
Frigidaire & GE Dryer Drive Motor Part Numbers 131560100 & WE17X10001
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com