Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairDanby Dishwasher Pump Outlet Hose Replacement #673000900182
Danby Dishwasher Pump Outlet Hose Replacement #673000900182
Skill Level
Total Parts Cost
$10.96Estimated Savings
$112.5008:09
- Description
This video provides step-by-step repair instructions for replacing the pump outlet hose on a Danby dishwasher. The most common reasons for replacing the hose are if the dishwasher is not filling or draining properly, or if the dishwasher is leaking.
All of the information for this dishwasher hose replacement video is applicable to the following brands:
Danby
Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, Channel Lock pliers
All of the information for this dishwasher hose replacement video is applicable to the following brands:
Danby
Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, Channel Lock pliers
Step By Step Instructions
1
To replace the pump outlet hose in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Open the dishwasher door and remove the lower dish rack.
13
Rotate the mounting nut clockwise to release the wash arm assembly.
14
Use channel-lock pliers to help unthread the axle connecter.
15
Remove the screw securing the circulation pump mounting bracket to the frame.
16
Tip the dishwasher back so it rests on its rear panel.
17
Detach the mounting bracket from the circulation pump.
18
Break the pinch clamp securing the outlet hose to the pump.
19
Pull the hose off of the pump.
20
Break the remaining pinch clamp to remove the fitting from the old hose.
21
Before you install the new pump outlet hose confirm that the o-ring is intact on the fitting.
22
Now slide a new clamp onto the hose insert the fitting into the hose and secure it with the clamp.
23
Slide a new clamp on the opposite end of the hose and align the slot in the hose with the tab on the port of the circulation pump.
24
Secure it with the clamp.
25
Realign the mounting bracket on the pump.
26
Return the dishwasher to its upright position.
27
Replace the screw to secure the pump mounting bracket to the frame.
28
Now rethread the axle connecter into the base fitting.
29
Position the wash arm assembly on the connecter and rotate the nut counter-clockwise to secure.
30
Replace the lower dish rack.
31
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
32
Adjust the leveling legs if necessary.
33
Replace the screws to secure the mounting brackets to the cabinet or countertop.
34
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
35
Make sure the hose is elevated above the connection point.
36
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
37
Connect the wires using the wire nuts.
38
Align the cover and replace the screw to secure.
39
Reconnect the water supply line to the inlet valve elbow fitting.
40
Realign the lower access panel and snap it into place.
41
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the pump outlet hose on a Danby dishwasher. The most common reasons for replacing the hose are if the dishwasher is not filling or draining properly, or if the dishwasher is leaking.
All of the information for this dishwasher hose replacement video is applicable to the following brands:
Danby
Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, Channel Lock pliers
All of the information for this dishwasher hose replacement video is applicable to the following brands:
Danby
Tools needed: 5/8" wrench, adjustable wrench, Phillip's head screwdriver, Channel Lock pliers
Step-By-Step Instructions
1
To replace the pump outlet hose in your dishwasher, you will need to uninstall the appliance. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Remove the lower access panel by lifting it up from the bottom to detach.
4
Use a 5/8th inch wrench or an adjustable wrench to help unthread the water supply line from the inlet valve elbow fitting be prepared for some water to spill.
5
Next, use a phillips-head screwdriver to unthread the screw securing the junction box cover. Then pull the cover off.
6
Note the location of the wires then untwist the wire nuts to disconnect the wires.
7
Unthread the strain relief nut if applicable and detach the strain relief from the junction box.
8
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
9
Open the dishwasher door and remove the mounting bracket screws.
10
To move the dishwasher, you may need to adjust the legs to lower the appliance.
11
Very carefully pull the dishwasher away from the cabinet.
12
Open the dishwasher door and remove the lower dish rack.
13
Rotate the mounting nut clockwise to release the wash arm assembly.
14
Use channel-lock pliers to help unthread the axle connecter.
15
Remove the screw securing the circulation pump mounting bracket to the frame.
16
Tip the dishwasher back so it rests on its rear panel.
17
Detach the mounting bracket from the circulation pump.
18
Break the pinch clamp securing the outlet hose to the pump.
19
Pull the hose off of the pump.
20
Break the remaining pinch clamp to remove the fitting from the old hose.
21
Before you install the new pump outlet hose confirm that the o-ring is intact on the fitting.
22
Now slide a new clamp onto the hose insert the fitting into the hose and secure it with the clamp.
23
Slide a new clamp on the opposite end of the hose and align the slot in the hose with the tab on the port of the circulation pump.
24
Secure it with the clamp.
25
Realign the mounting bracket on the pump.
26
Return the dishwasher to its upright position.
27
Replace the screw to secure the pump mounting bracket to the frame.
28
Now rethread the axle connecter into the base fitting.
29
Position the wash arm assembly on the connecter and rotate the nut counter-clockwise to secure.
30
Replace the lower dish rack.
31
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
32
Adjust the leveling legs if necessary.
33
Replace the screws to secure the mounting brackets to the cabinet or countertop.
34
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
35
Make sure the hose is elevated above the connection point.
36
Fully position the wire strain relief in the junction box and secure the strain relief nut if applicable.
37
Connect the wires using the wire nuts.
38
Align the cover and replace the screw to secure.
39
Reconnect the water supply line to the inlet valve elbow fitting.
40
Realign the lower access panel and snap it into place.
41
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com