Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Top-Load Washer Push Button Pad #W10596298
Whirlpool Top-Load Washer Push Button Pad #W10596298
Skill Level
Total Parts Cost
$52.15Estimated Savings
$112.5003:10
- Description
This video provides step-by-step repair instructions for replacing the push button pad on a Whirlpool washer. The most common reason for replacing the push button pad is if the washer won’t start.
This push button replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: putty knife, quarter-inch socket or nut driver
This push button replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: putty knife, quarter-inch socket or nut driver
Step By Step Instructions
1
Before you replace the push button pad on your washer be sure to unplug the power cord.
2
Insert a putty knife under the control panel to release the two spring clips securing the panel.
3
Pull the panel forward to release it.
4
Note the orientation of the switch wire connecters on the left side of the panel then disconnect them.
5
Disconnect the power wire connecter as well.
6
Use a quarter-inch socket or nut driver to unthread the two mounting screws securing the main control board.
7
Remove the center main control selector knob and lift the board up to detach it from the panel.
8
Remove the on-off push button.
9
Note the orientation of the old push button pad then pry it off.
10
Remove any mounting pad residue.
11
Install the new push button pad by first peeling the backing to expose the adhesive mounting strips.
12
Position the new pad on the control panel.
13
Align the on-off push button on the pad – note that the tab should be at the top.
14
Realign the control board tab with the slot in the panel and reposition the board.
15
Rethread the screws to secure.
16
Replace the selector knob.
17
Reconnect the switch wire connecters and the power supply wire connecter.
18
Realign the control panel on the upper rear panel, making sure the tabs are inserted into the slots in the main top.
19
Push the control panel down to snap the spring clips into place.
20
With the repair completed plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the push button pad on a Whirlpool washer. The most common reason for replacing the push button pad is if the washer won’t start.
This push button replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: putty knife, quarter-inch socket or nut driver
This push button replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: putty knife, quarter-inch socket or nut driver
Step-By-Step Instructions
1
Before you replace the push button pad on your washer be sure to unplug the power cord.
2
Insert a putty knife under the control panel to release the two spring clips securing the panel.
3
Pull the panel forward to release it.
4
Note the orientation of the switch wire connecters on the left side of the panel then disconnect them.
5
Disconnect the power wire connecter as well.
6
Use a quarter-inch socket or nut driver to unthread the two mounting screws securing the main control board.
7
Remove the center main control selector knob and lift the board up to detach it from the panel.
8
Remove the on-off push button.
9
Note the orientation of the old push button pad then pry it off.
10
Remove any mounting pad residue.
11
Install the new push button pad by first peeling the backing to expose the adhesive mounting strips.
12
Position the new pad on the control panel.
13
Align the on-off push button on the pad – note that the tab should be at the top.
14
Realign the control board tab with the slot in the panel and reposition the board.
15
Rethread the screws to secure.
16
Replace the selector knob.
17
Reconnect the switch wire connecters and the power supply wire connecter.
18
Realign the control panel on the upper rear panel, making sure the tabs are inserted into the slots in the main top.
19
Push the control panel down to snap the spring clips into place.
20
With the repair completed plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com