Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Top-Load Washer Drain Pump Replacement #W10661045
Whirlpool Top-Load Washer Drain Pump Replacement #W10661045
Skill Level
Total Parts Cost
$53.20Estimated Savings
$112.5003:23
- Description
This video provides step-by-step repair instructions for replacing the drain pump on a Whirlpool washer. The most common reason for replacing the drain pump is if the washer won’t drain.
This drain pump replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: pliers, 5/16th inch socket or nut driver
This drain pump replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: pliers, 5/16th inch socket or nut driver
Step By Step Instructions
1
Before you replace the drain pump in your washer be sure to unplug the power cord and shut off the water supply.
2
Remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
3
Release the retaining clamp and detach the drain hose from the outlet hose mounting flange.
4
Now use tape to secure the washer lid.
5
Carefully tip the washer back so it rests on its rear panel.
6
Release the drain pump wire cover, disconnect the wire connecter and unhook the wire from the retaining clip.
7
Release the spring clamp securing the hose to the pump and pull off the hose.
8
Use a 5/16th inch socket or nut driver to unthread the drain pump mounting screws.
9
With the screws unthreaded, remove the old pump.
10
Install the new drain pump by positioning it on the tub then thread the screws to secure.
11
Attach the hose to the pump and secure it with the clamp.
12
Connect the wire connecter, secure the wire under the retaining clip and close the cover.
13
Return the appliance to its upright position and remove the tape securing the lid.
14
Attach the drain hose to the outlet hose and secure it with the clamp.
15
Attach the hot and cold water supply lines.
16
With the repair completed turn the water supply back on plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain pump on a Whirlpool washer. The most common reason for replacing the drain pump is if the washer won’t drain.
This drain pump replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: pliers, 5/16th inch socket or nut driver
This drain pump replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: pliers, 5/16th inch socket or nut driver
Step-By-Step Instructions
1
Before you replace the drain pump in your washer be sure to unplug the power cord and shut off the water supply.
2
Remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
3
Release the retaining clamp and detach the drain hose from the outlet hose mounting flange.
4
Now use tape to secure the washer lid.
5
Carefully tip the washer back so it rests on its rear panel.
6
Release the drain pump wire cover, disconnect the wire connecter and unhook the wire from the retaining clip.
7
Release the spring clamp securing the hose to the pump and pull off the hose.
8
Use a 5/16th inch socket or nut driver to unthread the drain pump mounting screws.
9
With the screws unthreaded, remove the old pump.
10
Install the new drain pump by positioning it on the tub then thread the screws to secure.
11
Attach the hose to the pump and secure it with the clamp.
12
Connect the wire connecter, secure the wire under the retaining clip and close the cover.
13
Return the appliance to its upright position and remove the tape securing the lid.
14
Attach the drain hose to the outlet hose and secure it with the clamp.
15
Attach the hot and cold water supply lines.
16
With the repair completed turn the water supply back on plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com