Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Top Load Washer Control Board Replacement #W10711300
Whirlpool Top Load Washer Control Board Replacement #W10711300
Skill Level
Total Parts Cost
$393.76Estimated Savings
$112.5003:29
- Description
This video provides step-by-step repair instructions for replacing the control board on a Whirlpool washer. The most common reason for replacing the control board is if the washer won’t start.
This control board replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: 7/16th socket and extension
This control board replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: 7/16th socket and extension
Step By Step Instructions
1
Before you replace the washer control board assembly be sure to unplug the power cord.
2
Insert a putty knife under the control panel to release the two spring clips securing the panel.
3
Pull the panel forward to release it.
4
Note the orientation of the switch wire connecters then disconnect them from the control board.
5
Disconnect the power wire connecter as well.
6
You can use a flat-head screwdriver or pliers to release the wire bracket and retainer.
7
Detach the air pressure tube.
8
Use a quarter-inch socket or nut driver to unthread the two mounting screws securing the control board.
9
Remove the center main control selector knob and lift the old control board assembly up to detach it from the panel.
10
Prepare the new control board assembly for installation by transferring the wire retaining bracket from the old assembly to the new one.
11
Align the control board tab with the slot in the panel and position the board.
12
Thread the screws to secure.
13
Replace the selector knob.
14
Connect all of the wire connecters to the appropriate terminals on the new board.
15
Secure the wires as necessary.
16
Attach the air pressure tube to the board.
17
Realign the control panel on the upper rear panel, making sure the tabs are inserted into the slots in the main top.
18
Push the control panel down to snap the spring clips into place.
19
With the repair completed plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the control board on a Whirlpool washer. The most common reason for replacing the control board is if the washer won’t start.
This control board replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: 7/16th socket and extension
This control board replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: 7/16th socket and extension
Step-By-Step Instructions
1
Before you replace the washer control board assembly be sure to unplug the power cord.
2
Insert a putty knife under the control panel to release the two spring clips securing the panel.
3
Pull the panel forward to release it.
4
Note the orientation of the switch wire connecters then disconnect them from the control board.
5
Disconnect the power wire connecter as well.
6
You can use a flat-head screwdriver or pliers to release the wire bracket and retainer.
7
Detach the air pressure tube.
8
Use a quarter-inch socket or nut driver to unthread the two mounting screws securing the control board.
9
Remove the center main control selector knob and lift the old control board assembly up to detach it from the panel.
10
Prepare the new control board assembly for installation by transferring the wire retaining bracket from the old assembly to the new one.
11
Align the control board tab with the slot in the panel and position the board.
12
Thread the screws to secure.
13
Replace the selector knob.
14
Connect all of the wire connecters to the appropriate terminals on the new board.
15
Secure the wires as necessary.
16
Attach the air pressure tube to the board.
17
Realign the control panel on the upper rear panel, making sure the tabs are inserted into the slots in the main top.
18
Push the control panel down to snap the spring clips into place.
19
With the repair completed plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com