Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Dishwasher Door Spring Replacement #WP8270020
KitchenAid Dishwasher Door Spring Replacement #WP8270020
Skill Level
Total Parts Cost
$30.10Estimated Savings
$112.5005:49
- Description
This video provides step-by-step repair instructions for replacing the door spring on a KitchenAid dishwasher. The most common reason for replacing the spring is if the door opens too quickly or is difficult to open.
All of the information for this door spring replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
All of the information for this door spring replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
Step By Step Instructions
1
Before you replace a door spring on your dishwasher be sure to turn off the power to the appliance
2
Shut off the water supply valve.
3
Use a quarter-inch nut driver or a phillips-head screwdriver to unthread the mounting screws securing the lower access panels.
4
Remove the outer panel along with the inner panel and the attached insulation.
5
Use channel-lock pliers to unthread the water supply line elbow fitting from the inlet valve be prepared for some water to spill.
6
Next, use a quarter-inch socket or nut driver to unthread the screw to release the terminal box from the right support rail.
7
Detach the cover note the orientation of the power wires then untwist the wire nuts to disconnect the wires.
8
Unthread the screw to release the grounding wire.
9
Unthread the strain relief nut and detach the strain relief and power wires from the terminal box.
10
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
11
Open the dishwasher door and remove the mounting bracket screws.
12
To move the dishwasher, you may need to adjust the legs to lower the appliance.
13
Very carefully pull the dishwasher away from the cabinet.
14
If still intact, detach the old door spring from the frame and the door cable.
15
Install the new door spring by first attaching the door cable to one end then hook the opposite end of the spring on the frame.
16
Reposition the insulation blanket on the dishwasher if necessary.
17
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
18
Adjust the leveling legs if necessary.
19
Replace the screws to secure the mounting brackets to the cabinet or countertop.
20
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
21
Make sure the hose is elevated above the connection point.
22
Fully position the wires and strain relief in the terminal box then thread and tighten the strain relief nut.
23
Secure the grounding wire with the screw.
24
Join the black wires together and the white wires together and secure them with the wire nuts.
25
With the wires positioned inside the terminal box, realign the cover then thread the screw to secure the box to the support rail.
26
Reconnect the water supply line elbow fitting to the inlet valve.
27
Reposition the inner access panel and insulation followed by the outer panel.
28
Rethread and tighten the screws to secure.
29
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the door spring on a KitchenAid dishwasher. The most common reason for replacing the spring is if the door opens too quickly or is difficult to open.
All of the information for this door spring replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
All of the information for this door spring replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
Step-By-Step Instructions
1
Before you replace a door spring on your dishwasher be sure to turn off the power to the appliance
2
Shut off the water supply valve.
3
Use a quarter-inch nut driver or a phillips-head screwdriver to unthread the mounting screws securing the lower access panels.
4
Remove the outer panel along with the inner panel and the attached insulation.
5
Use channel-lock pliers to unthread the water supply line elbow fitting from the inlet valve be prepared for some water to spill.
6
Next, use a quarter-inch socket or nut driver to unthread the screw to release the terminal box from the right support rail.
7
Detach the cover note the orientation of the power wires then untwist the wire nuts to disconnect the wires.
8
Unthread the screw to release the grounding wire.
9
Unthread the strain relief nut and detach the strain relief and power wires from the terminal box.
10
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
11
Open the dishwasher door and remove the mounting bracket screws.
12
To move the dishwasher, you may need to adjust the legs to lower the appliance.
13
Very carefully pull the dishwasher away from the cabinet.
14
If still intact, detach the old door spring from the frame and the door cable.
15
Install the new door spring by first attaching the door cable to one end then hook the opposite end of the spring on the frame.
16
Reposition the insulation blanket on the dishwasher if necessary.
17
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
18
Adjust the leveling legs if necessary.
19
Replace the screws to secure the mounting brackets to the cabinet or countertop.
20
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
21
Make sure the hose is elevated above the connection point.
22
Fully position the wires and strain relief in the terminal box then thread and tighten the strain relief nut.
23
Secure the grounding wire with the screw.
24
Join the black wires together and the white wires together and secure them with the wire nuts.
25
With the wires positioned inside the terminal box, realign the cover then thread the screw to secure the box to the support rail.
26
Reconnect the water supply line elbow fitting to the inlet valve.
27
Reposition the inner access panel and insulation followed by the outer panel.
28
Rethread and tighten the screws to secure.
29
With the repair completed, turn the water supply back on as well as the power and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com