Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Dishwasher Replace Turbidity Sensor #WPW10705575
KitchenAid Dishwasher Replace Turbidity Sensor #WPW10705575
Skill Level
Total Parts Cost
$35.89Estimated Savings
$112.5002:09
- Description
This video provides step-by-step repair instructions for replacing the turbidity sensor on a KitchenAid dishwasher. The most common reason for replacing the sensor is if the dishwasher is not draining properly.
All of the information for this turbidity sensor replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
All of the information for this turbidity sensor replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
Step By Step Instructions
1
Before you replace the turbidity sensor in your dishwasher be sure to turn off the power to the appliance.
2
Use a quarter-inch nut driver or a phillips-head screwdriver to unthread the mounting screws securing the lower access panels.
3
Remove the outer panel along with the inner panel and the attached insulation.
4
Reach under the dishwasher and rotate the turbidity sensor counter-clockwise to detach it from the sump.
5
Disconnect the wire connecter to fully remove the old sensor.
6
Install the new turbidity sensor by first connecting the wire connecter then insert the sensor into the sump and rotate clockwise to lock it into place.
7
Reposition the inner access panel and insulation followed by the outer panel.
8
Rethread and tighten the screws to secure.
9
With the repair completed turn the power back on and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the turbidity sensor on a KitchenAid dishwasher. The most common reason for replacing the sensor is if the dishwasher is not draining properly.
All of the information for this turbidity sensor replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
All of the information for this turbidity sensor replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, Channel Lock pliers, phillips head screwdriver
Step-By-Step Instructions
1
Before you replace the turbidity sensor in your dishwasher be sure to turn off the power to the appliance.
2
Use a quarter-inch nut driver or a phillips-head screwdriver to unthread the mounting screws securing the lower access panels.
3
Remove the outer panel along with the inner panel and the attached insulation.
4
Reach under the dishwasher and rotate the turbidity sensor counter-clockwise to detach it from the sump.
5
Disconnect the wire connecter to fully remove the old sensor.
6
Install the new turbidity sensor by first connecting the wire connecter then insert the sensor into the sump and rotate clockwise to lock it into place.
7
Reposition the inner access panel and insulation followed by the outer panel.
8
Rethread and tighten the screws to secure.
9
With the repair completed turn the power back on and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com