Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Dishwasher Control Board Replacement #W10854228
KitchenAid Dishwasher Control Board Replacement #W10854228
Skill Level
Total Parts Cost
$158.79Estimated Savings
$112.5003:05
- Description
This video provides step-by-step repair instructions for replacing the control board on a KitchenAid dishwasher. The most common reason for replacing the board is if the dishwasher is not working at all, and other commonly replaced parts are working properly.
All of the information for this control board replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, flat head screwdriver, phillips head screwdriver
All of the information for this control board replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, flat head screwdriver, phillips head screwdriver
Step By Step Instructions
1
Before you replace the dishwasher control board, be sure to turn off the power to the appliance.
2
Use a quarter-inch nut driver or a Phillips head screwdriver to unthread the mounting screws securing the lower access panels.
3
Remove the outer panel along with the inner panel and the attached insulation.
4
Reach under the dishwasher and release the Control Board wires from the sump clip.
5
Detach the wire harness retainer from the control board mounting bracket, and you can remove the assembly from the bracket.
6
Use a small flat-head screwdriver to depress the tabs to pry the control board cover off.
7
Note the orientation of the wires connected to the control board, then disconnect them.
8
Install the new control board by first connecting the wire connectors to the appropriate terminals.
9
Align the cover, tuck the wires in, and snap on the cover.
10
Position the control board in the mounting bracket and snap the wire harness retainer into the slot in the bracket.
11
Hook the wires onto the sump clip.
12
Reposition the inner access panel and insulation, followed by the outer panel.
13
Rethread and tighten the screws to secure.
14
With the repair completed, turn the power back on, and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the control board on a KitchenAid dishwasher. The most common reason for replacing the board is if the dishwasher is not working at all, and other commonly replaced parts are working properly.
All of the information for this control board replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, flat head screwdriver, phillips head screwdriver
All of the information for this control board replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Tools needed: 1/4" nut driver, flat head screwdriver, phillips head screwdriver
Step-By-Step Instructions
1
Before you replace the dishwasher control board, be sure to turn off the power to the appliance.
2
Use a quarter-inch nut driver or a Phillips head screwdriver to unthread the mounting screws securing the lower access panels.
3
Remove the outer panel along with the inner panel and the attached insulation.
4
Reach under the dishwasher and release the Control Board wires from the sump clip.
5
Detach the wire harness retainer from the control board mounting bracket, and you can remove the assembly from the bracket.
6
Use a small flat-head screwdriver to depress the tabs to pry the control board cover off.
7
Note the orientation of the wires connected to the control board, then disconnect them.
8
Install the new control board by first connecting the wire connectors to the appropriate terminals.
9
Align the cover, tuck the wires in, and snap on the cover.
10
Position the control board in the mounting bracket and snap the wire harness retainer into the slot in the bracket.
11
Hook the wires onto the sump clip.
12
Reposition the inner access panel and insulation, followed by the outer panel.
13
Rethread and tighten the screws to secure.
14
With the repair completed, turn the power back on, and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com