Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKenmore Top-Load Washer Lid Switch Assembly #WP8054980
Kenmore Top-Load Washer Lid Switch Assembly #WP8054980
Skill Level
Total Parts Cost
$117.79Estimated Savings
$112.5003:47
- Description
This video provides step-by-step repair instructions for replacing the lid switch assembly on a Kenmore Top-Load washing machine. The most common reason for replacing the lid switch is if the washer won't run with the lid shut.
All of the information for this lid switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, 5/16" socket
All of the information for this lid switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, 5/16" socket
Step By Step Instructions
1
Before you replace the lid switch assembly in your washer be sure to unplug the power cord.
2
Detach the two control panel end caps by pulling them off from the top.
3
Use a phillips-head screwdriver to unthread the two screws securing the control panel.
4
Lift up the control panel.
5
Next, disconnect the lid switch wire connecter.
6
Using a flat-head screwdriver, release the spring clips securing the cabinet to the rear panel.
7
Tilt the cabinet toward you, slide forward and remove.
8
Use a 5/16th inch socket or nut driver to unthread the screw securing the grounding wire.
9
Depress the retaining tabs to release the lid switch wire connecter from the main top.
10
Using a phillips-head screwdriver, unthread the lid switch mounting screws.
11
Lift up the washer lid, depress the tab and you can remove the old assembly.
12
Install the new lid switch assembly by positioning it under the main top.
13
Make sure the actuator lever is under the hinge arm.
14
Thread and tighten the mounting screws to secure.
15
Snap the wire connecter into place and secure the grounding wire with the screw.
16
Reinstall the cabinet by sliding the front edge of the cabinet underneath the base frame.
17
Use your foot to push it into position.
18
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
19
Make sure the sides of the cabinet are properly aligned with the rear panel.
20
Reinstall the spring clips to secure the cabinet.
21
Connect the lid switch wire connecter.
22
Lower the control panel and snap the retaining clips into the slots in the main top.
23
Rethread and tighten the screws to secure the control panel.
24
Realign the end caps and snap them into place.
25
With the repair completed plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the lid switch assembly on a Kenmore Top-Load washing machine. The most common reason for replacing the lid switch is if the washer won't run with the lid shut.
All of the information for this lid switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, 5/16" socket
All of the information for this lid switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, 5/16" socket
Step-By-Step Instructions
1
Before you replace the lid switch assembly in your washer be sure to unplug the power cord.
2
Detach the two control panel end caps by pulling them off from the top.
3
Use a phillips-head screwdriver to unthread the two screws securing the control panel.
4
Lift up the control panel.
5
Next, disconnect the lid switch wire connecter.
6
Using a flat-head screwdriver, release the spring clips securing the cabinet to the rear panel.
7
Tilt the cabinet toward you, slide forward and remove.
8
Use a 5/16th inch socket or nut driver to unthread the screw securing the grounding wire.
9
Depress the retaining tabs to release the lid switch wire connecter from the main top.
10
Using a phillips-head screwdriver, unthread the lid switch mounting screws.
11
Lift up the washer lid, depress the tab and you can remove the old assembly.
12
Install the new lid switch assembly by positioning it under the main top.
13
Make sure the actuator lever is under the hinge arm.
14
Thread and tighten the mounting screws to secure.
15
Snap the wire connecter into place and secure the grounding wire with the screw.
16
Reinstall the cabinet by sliding the front edge of the cabinet underneath the base frame.
17
Use your foot to push it into position.
18
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
19
Make sure the sides of the cabinet are properly aligned with the rear panel.
20
Reinstall the spring clips to secure the cabinet.
21
Connect the lid switch wire connecter.
22
Lower the control panel and snap the retaining clips into the slots in the main top.
23
Rethread and tighten the screws to secure the control panel.
24
Realign the end caps and snap them into place.
25
With the repair completed plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com