Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Canopy Vent Hood 36" Insulation Replacement #W10735407
Kitchenaid Canopy Vent Hood 36" Insulation Replacement #W10735407
Skill Level
Total Parts Cost
$106.03Estimated Savings
$112.5006:26
- Description
This video provides step-by-step repair instructions for replacing the insulation on a Kitchenaid Canopy Vent Hood (model #KVWB400DSS). The most common reason for replacing the insulation is if it is damaged or dirty.
All of the information for this insulation replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: flat head screwdriver, T-10 Torx bit
All of the information for this insulation replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: flat head screwdriver, T-10 Torx bit
Step By Step Instructions
1
Before you replace the insulation in your canopy vent hood, be sure to turn off the power supply to the hood.
2
Place a blanket over the cooktop to protect the surface.
3
Rotate the access panel down.
4
Use a flathead screwdriver to loosen the two screws securing the panel.
5
Fully unthread the screws to release the panel.
6
Remove both grease filters.
7
Use a T10 Torx bit to unthread the screws to release the filter frames.
8
Next, unthread the screws to release the blower assembly cover.
9
Unthread the screws securing the light assembly panel.
10
Slide the panel back to detach.
11
Disconnect the light assembly wire connectors and set the panel aside.
12
For easier access to install the insulation, unthread the screws securing the control housing to the mounting rail.
13
Detach the power supply cable from the retaining clip and move the control housing off of the mounting rail.
14
Use a small flat-head screwdriver to release the tabs to disconnect the main control assembly wire connector.
15
You can now pull the old insulation free of the retaining brackets.
16
Install the new insulation by aligning it in the hood under the retaining brackets.
17
With the insulation in place, reconnect the control assembly wire connector.
18
Then, reposition the control housing on the mounting rail and secure the power supply cable in the retaining clip.
19
Thread and tighten the screws to secure the housing.
20
Install the light assembly panel by first connecting the wire connectors.
21
Realign the panel, slide it forward, then thread and tighten the screws.
22
Reposition the blower assembly cover and secure it with the screws.
23
Realign the grease filter frames and rethread the screws to secure.
24
Replace the grease filters.
25
Align the access panel on the hinges, then thread and tighten the two screws to secure.
26
Once the rear of the panel is secured, rotate the panel up and snap it into position.
27
With the repair completed, turn the power supply back on and the vent hood should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the insulation on a Kitchenaid Canopy Vent Hood (model #KVWB400DSS). The most common reason for replacing the insulation is if it is damaged or dirty.
All of the information for this insulation replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: flat head screwdriver, T-10 Torx bit
All of the information for this insulation replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: flat head screwdriver, T-10 Torx bit
Step-By-Step Instructions
1
Before you replace the insulation in your canopy vent hood, be sure to turn off the power supply to the hood.
2
Place a blanket over the cooktop to protect the surface.
3
Rotate the access panel down.
4
Use a flathead screwdriver to loosen the two screws securing the panel.
5
Fully unthread the screws to release the panel.
6
Remove both grease filters.
7
Use a T10 Torx bit to unthread the screws to release the filter frames.
8
Next, unthread the screws to release the blower assembly cover.
9
Unthread the screws securing the light assembly panel.
10
Slide the panel back to detach.
11
Disconnect the light assembly wire connectors and set the panel aside.
12
For easier access to install the insulation, unthread the screws securing the control housing to the mounting rail.
13
Detach the power supply cable from the retaining clip and move the control housing off of the mounting rail.
14
Use a small flat-head screwdriver to release the tabs to disconnect the main control assembly wire connector.
15
You can now pull the old insulation free of the retaining brackets.
16
Install the new insulation by aligning it in the hood under the retaining brackets.
17
With the insulation in place, reconnect the control assembly wire connector.
18
Then, reposition the control housing on the mounting rail and secure the power supply cable in the retaining clip.
19
Thread and tighten the screws to secure the housing.
20
Install the light assembly panel by first connecting the wire connectors.
21
Realign the panel, slide it forward, then thread and tighten the screws.
22
Reposition the blower assembly cover and secure it with the screws.
23
Realign the grease filter frames and rethread the screws to secure.
24
Replace the grease filters.
25
Align the access panel on the hinges, then thread and tighten the two screws to secure.
26
Once the rear of the panel is secured, rotate the panel up and snap it into position.
27
With the repair completed, turn the power supply back on and the vent hood should be ready for use.
Applicable Product Model
Parts Needed
Insulation
$106.03
Total$0.00
Related Articles & Videos
05:33
Part Replacement
Kitchenaid Canopy Vent Hood Main Control Assembly Replacement #WPW10727063
05:10
Part Replacement
Kitchenaid Canopy Vent Hood Blower Assembly Replacement #W10735405
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com