Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairHonda Small Engine O-Ring Replacement #91353-671-003
Honda Small Engine O-Ring Replacement #91353-671-003
Skill Level
Total Parts Cost
$4.63Estimated Savings
$112.5002:29
- Description
This video provides step-by-step instructions for replacing the o-ring on Honda small engines, commonly found in Honda lawn mowers, riding tractors, zero-turn radius mowers, pressure washers, generators, log splitters, and snow blowers. The most common reason for replacing the o-ring is if it is leaking oil.
All of the information in this o-ring replacement video is applicable to the following brands: Honda
Tools used: socket wrench, snap ring pliers, multi-screwdriver, flat-head bit
All of the information in this o-ring replacement video is applicable to the following brands: Honda
Tools used: socket wrench, snap ring pliers, multi-screwdriver, flat-head bit
Step By Step Instructions
1
Before you begin the repair, make sure the engine has cooled.
2
Remove the wire and boot from the spark plug and perform the procedure with little or no gasoline in the tank.
3
Your first step is to remove the two nuts securing the gas tank.
4
Next, adjust the throttle as necessary to access the tank's mounting bolt and remove it.
5
Now, lift the gas tank upward, release the clamp securing the fuel line, and pull the fuel line off of the tank.
6
Be aware, some gasoline may spill out.
7
After placing the tank on a sturdy surface, use a deep well socket to remove the fuel filter.
8
Use a small flat-head screwdriver to remove the old o-ring if still intact.
9
Install the new o-ring by positioning it onto the fuel filter.
10
Now, thread the filter into the gas tank and secure it with the socket.
11
Be careful not to over-tighten or damage the filter.
12
Reconnect the fuel line to the gas tank and secure the clamp.
13
Using locking pliers to support the line will make this step easier.
14
If applicable, remove the locking pliers, then reposition the gas tank.
15
Replace the mounting bolt and nuts.
16
With the repair complete, reattach the spark plug wire and boot.
Description
This video provides step-by-step instructions for replacing the o-ring on Honda small engines, commonly found in Honda lawn mowers, riding tractors, zero-turn radius mowers, pressure washers, generators, log splitters, and snow blowers. The most common reason for replacing the o-ring is if it is leaking oil.
All of the information in this o-ring replacement video is applicable to the following brands: Honda
Tools used: socket wrench, snap ring pliers, multi-screwdriver, flat-head bit
All of the information in this o-ring replacement video is applicable to the following brands: Honda
Tools used: socket wrench, snap ring pliers, multi-screwdriver, flat-head bit
Step-By-Step Instructions
1
Before you begin the repair, make sure the engine has cooled.
2
Remove the wire and boot from the spark plug and perform the procedure with little or no gasoline in the tank.
3
Your first step is to remove the two nuts securing the gas tank.
4
Next, adjust the throttle as necessary to access the tank's mounting bolt and remove it.
5
Now, lift the gas tank upward, release the clamp securing the fuel line, and pull the fuel line off of the tank.
6
Be aware, some gasoline may spill out.
7
After placing the tank on a sturdy surface, use a deep well socket to remove the fuel filter.
8
Use a small flat-head screwdriver to remove the old o-ring if still intact.
9
Install the new o-ring by positioning it onto the fuel filter.
10
Now, thread the filter into the gas tank and secure it with the socket.
11
Be careful not to over-tighten or damage the filter.
12
Reconnect the fuel line to the gas tank and secure the clamp.
13
Using locking pliers to support the line will make this step easier.
14
If applicable, remove the locking pliers, then reposition the gas tank.
15
Replace the mounting bolt and nuts.
16
With the repair complete, reattach the spark plug wire and boot.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com