Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairCabrio/Oasis Top Load Washer Motor Stator #W10419333
Cabrio/Oasis Top Load Washer Motor Stator #W10419333
Skill Level
Total Parts Cost
$205.39Estimated Savings
$112.5003:10
- Description
This video provides step-by-step repair instructions for replacing the motor stator on a Cabrio/Oasis top-loading washing machine. The most common reasons for replacing the motor stator are when the washer won’t agitate, won’t spin, or won’t spin or agitate.
All of the information for this motor stator replacement video is applicable to the following brands:
Whirlpool, Kenmore, Maytag
Tools needed: wrench, nutdriver, flathead screwdriver
All of the information for this motor stator replacement video is applicable to the following brands:
Whirlpool, Kenmore, Maytag
Tools needed: wrench, nutdriver, flathead screwdriver
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning and turn off the hot and cold water supply valves.
2
Your first step is to remove the hoses from the water inlet valve.
3
Be prepared for some water to spill out.
4
Make sure the drain hose is detached from the standpipe or laundry tub.
5
Next, use tape to secure the washer lid.
6
Now, carefully tip the washer forward so its front rests on a towel or carpet.
7
Use a quarter-inch Allen wrench to fully loosen the rotor mounting screw, then pull the rotor off.
8
Be aware, this may require some effort.
9
Now, remove the mounting bolts securing the stator and remove the front spacer.
10
Pull the old stator off of the tub shaft along with the shield and the rear spacer.
11
Detach the power connector.
12
Use a small flat-head screwdriver to help detach the rotor position sensor.
13
You're now ready to install the new stator.
14
Connect the rotor position sensor to the new stator by aligning its cover with the indentations on the stator housing and snapping it into place.
15
Attach the power connector and secure the wire harness.
16
Position the shield on the new stator along with the rear spacer and align the assembly on the tub shaft.
17
Position the front spacer and secure the mounting bolts.
18
Carefully slide the rotor onto the tub shaft.
19
Fully tighten the mounting screw.
20
Now, carefully lift the washer to its upright position.
21
Remove the tape securing the lid and attach the drain hose to the standpipe or laundry tub.
22
Reattach the hoses to the inlet valve.
23
Turn the water supply back on and plug the appliance back in to make sure it's functioning properly.
Description
This video provides step-by-step repair instructions for replacing the motor stator on a Cabrio/Oasis top-loading washing machine. The most common reasons for replacing the motor stator are when the washer won’t agitate, won’t spin, or won’t spin or agitate.
All of the information for this motor stator replacement video is applicable to the following brands:
Whirlpool, Kenmore, Maytag
Tools needed: wrench, nutdriver, flathead screwdriver
All of the information for this motor stator replacement video is applicable to the following brands:
Whirlpool, Kenmore, Maytag
Tools needed: wrench, nutdriver, flathead screwdriver
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning and turn off the hot and cold water supply valves.
2
Your first step is to remove the hoses from the water inlet valve.
3
Be prepared for some water to spill out.
4
Make sure the drain hose is detached from the standpipe or laundry tub.
5
Next, use tape to secure the washer lid.
6
Now, carefully tip the washer forward so its front rests on a towel or carpet.
7
Use a quarter-inch Allen wrench to fully loosen the rotor mounting screw, then pull the rotor off.
8
Be aware, this may require some effort.
9
Now, remove the mounting bolts securing the stator and remove the front spacer.
10
Pull the old stator off of the tub shaft along with the shield and the rear spacer.
11
Detach the power connector.
12
Use a small flat-head screwdriver to help detach the rotor position sensor.
13
You're now ready to install the new stator.
14
Connect the rotor position sensor to the new stator by aligning its cover with the indentations on the stator housing and snapping it into place.
15
Attach the power connector and secure the wire harness.
16
Position the shield on the new stator along with the rear spacer and align the assembly on the tub shaft.
17
Position the front spacer and secure the mounting bolts.
18
Carefully slide the rotor onto the tub shaft.
19
Fully tighten the mounting screw.
20
Now, carefully lift the washer to its upright position.
21
Remove the tape securing the lid and attach the drain hose to the standpipe or laundry tub.
22
Reattach the hoses to the inlet valve.
23
Turn the water supply back on and plug the appliance back in to make sure it's functioning properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com