Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid 5 Door Refrigerator Damper Control Assembly Replacement WPW10248595 
KitchenAid 5 Door Refrigerator Damper Control Assembly Replacement WPW10248595
Skill Level
Total Parts Cost
$104.58Estimated Savings
$112.5013:08
- Description
This video provides step-by-step repair instructions for replacing the damper control assembly on a KitchenAid 5 Door Refrigerator (Model KRMF706ESS01). The most common reason for replacing this part is if the refrigerator is not cooling properly.
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step By Step Instructions
1
KitchenAid Five-Door Refrigerator - KRMF706ESS01
2
Refrigerator Damper Control Assembly Replacement
3
heavy, sharp, shock, water
4
Shock
5
unplug the power cord
6
use a Phillip's-head screwdriver to unthread the screws securing the two top hinge covers
7
lift off the covers
8
to remove the top left hinge, lift up the clasp and detach the dispenser water supply line
9
depress the catch to disconnect the wire connecter
10
unthread the screw to release the grounding wire
11
use a t-25 torx bit to unthread the front and rear mounting screws securing the top hinges to the appliance
12
Heavy
13
support each door as you remove the hinge
14
open each door to a ninety degree position and have an assistant help you lift the doors off
15
unthread the three mounting screws to release the left and right center hinges from the frame
16
remove all of the shelving from the refrigerator compartment
17
Fragile
18
lift out the glass covering the crisper drawers
19
remove the glass frame along with the drawers
20
lift out the storage tray
21
open the pantry drawers and remove both bins
22
push up on the levers at the bottom of both drawer glide brackets to release the right drawer front from the brackets
23
slide the glides back into the refrigerator
24
to remove the left drawer front, you will need to detach the wire connection cover
25
then use a small flat-head screwdriver to help disconnect the temperature control wire connecter
26
you can now release the drawer front from the drawer glide brackets and fully remove it
27
depress the tabs to release the wire harness access cover on the left side of the crisper drawer support panel
28
disconnect the light switch harness
29
release the tabs securing the crisper drawer support panel
30
lift the front of the panel up and pull forward to remove
31
use a thin putty knife to detach the vertical frame mullion then disconnect the wire connecter
32
detach the access cover on the right side of the interior liner
33
disconnect the two light switch wire connecters
34
use a quarter-inch socket to unthread the screw securing the horizontal frame mullion assembly
35
release the tabs on both sides of the assembly and fully remove
36
Heavy
37
lift out the center pantry drawer slide assembly
38
slide the rear support bar to the left to detach
39
depress the water filter cover to release it
40
rotate the filter counter-clockwise to remove
41
use a quarter-inch socket to unthread the two screws securing the water reservoir access panel
42
pull the panel down using a flat-head screwdriver to help detach the mounting posts
43
disconnect the LED light wire connecter and set the panel aside
44
use a flat-head screwdriver to help release the air tower
45
unthread the four mounting screws securing the evaporator motor cover
46
pull the cover forward from the top to remove
47
disconnect the damper control assembly wire connecter
48
release the wires from the retaining clips and tape
49
fully remove the old assembly
50
prepare the new damper control assembly for installation by applying two pieces of foam tape
51
secure the assembly in the polystyrene foam insulating blocks
52
slide the new assembly into place in the evaporator housing
53
connect the wire connecter
54
secure the wires under the retaining clip and replace tape
55
realign the evaporator cover
56
rethread the screws
57
reinstall the air tower by aligning the bottom first then pushing into position
58
reinstall the water reservoir access panel by connecting the LED wire connecter
59
insert the three tabs at the back into the slots then snap the mounting posts into place
60
rethread the screws
61
reinstall the water filter and close the cover
62
reinstall the rear support bar
63
reposition the center pantry drawer slide assembly
64
keeping the wires secured, reinstall the horizontal frame mullion assembly
65
rethread the screws
66
reconnect the wire connecters and replace the access cover
67
reconnect the vertical frame mullion wire connecter
68
make sure the tabs are straight then snap the frame into place
69
feed the crisper drawer support panel wire harness through the side housing as you reposition the support panel
70
connect the wire connecter and replace the cover
71
replace the pantry drawer fronts by first pushing up on the lever at the bottom of the glide bracket to open
72
insert the drawer front bracket into the glide bracket and release the lever to lock the drawer front in place
73
repeat for opposite side
74
reconnect the temperature control wire connecter on the left drawer and replace the cover
75
reposition the drawer bins
76
replace the storage tray
77
reposition the crisper drawers
78
realign the glass frame and replace the glass
79
replace the shelving
80
confirm the closing cam is properly set
81
with the hinge base parallel with the door, insert the hinge pin and bushing into the hole
82
rotate the hinge so the base is at a ninety degree angle to the door to reset the cam
83
realign both center hinges on the frame
84
thread the mounting screws to secure
85
make sure the hinge bushing and washer are intact
86
set each door on its respective bushing at a ninety degree angle and confirm it closes properly
87
reinstall the top hinge by inserting the wires and water line through the hole in the hinge
88
thread the mounting screws to secure
89
slide the bushing over the wires and water line and insert it into the hinge
90
connect the wire
91
thread the screw to secure the grounding wire
92
Water
93
reattach the water supply line
94
replace both hinge cover and secure them with the screws
95
Shock
96
plug the power cord back in
Description
This video provides step-by-step repair instructions for replacing the damper control assembly on a KitchenAid 5 Door Refrigerator (Model KRMF706ESS01). The most common reason for replacing this part is if the refrigerator is not cooling properly.
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step-By-Step Instructions
1
KitchenAid Five-Door Refrigerator - KRMF706ESS01
2
Refrigerator Damper Control Assembly Replacement
3
heavy, sharp, shock, water
4
Shock
5
unplug the power cord
6
use a Phillip's-head screwdriver to unthread the screws securing the two top hinge covers
7
lift off the covers
8
to remove the top left hinge, lift up the clasp and detach the dispenser water supply line
9
depress the catch to disconnect the wire connecter
10
unthread the screw to release the grounding wire
11
use a t-25 torx bit to unthread the front and rear mounting screws securing the top hinges to the appliance
12
Heavy
13
support each door as you remove the hinge
14
open each door to a ninety degree position and have an assistant help you lift the doors off
15
unthread the three mounting screws to release the left and right center hinges from the frame
16
remove all of the shelving from the refrigerator compartment
17
Fragile
18
lift out the glass covering the crisper drawers
19
remove the glass frame along with the drawers
20
lift out the storage tray
21
open the pantry drawers and remove both bins
22
push up on the levers at the bottom of both drawer glide brackets to release the right drawer front from the brackets
23
slide the glides back into the refrigerator
24
to remove the left drawer front, you will need to detach the wire connection cover
25
then use a small flat-head screwdriver to help disconnect the temperature control wire connecter
26
you can now release the drawer front from the drawer glide brackets and fully remove it
27
depress the tabs to release the wire harness access cover on the left side of the crisper drawer support panel
28
disconnect the light switch harness
29
release the tabs securing the crisper drawer support panel
30
lift the front of the panel up and pull forward to remove
31
use a thin putty knife to detach the vertical frame mullion then disconnect the wire connecter
32
detach the access cover on the right side of the interior liner
33
disconnect the two light switch wire connecters
34
use a quarter-inch socket to unthread the screw securing the horizontal frame mullion assembly
35
release the tabs on both sides of the assembly and fully remove
36
Heavy
37
lift out the center pantry drawer slide assembly
38
slide the rear support bar to the left to detach
39
depress the water filter cover to release it
40
rotate the filter counter-clockwise to remove
41
use a quarter-inch socket to unthread the two screws securing the water reservoir access panel
42
pull the panel down using a flat-head screwdriver to help detach the mounting posts
43
disconnect the LED light wire connecter and set the panel aside
44
use a flat-head screwdriver to help release the air tower
45
unthread the four mounting screws securing the evaporator motor cover
46
pull the cover forward from the top to remove
47
disconnect the damper control assembly wire connecter
48
release the wires from the retaining clips and tape
49
fully remove the old assembly
50
prepare the new damper control assembly for installation by applying two pieces of foam tape
51
secure the assembly in the polystyrene foam insulating blocks
52
slide the new assembly into place in the evaporator housing
53
connect the wire connecter
54
secure the wires under the retaining clip and replace tape
55
realign the evaporator cover
56
rethread the screws
57
reinstall the air tower by aligning the bottom first then pushing into position
58
reinstall the water reservoir access panel by connecting the LED wire connecter
59
insert the three tabs at the back into the slots then snap the mounting posts into place
60
rethread the screws
61
reinstall the water filter and close the cover
62
reinstall the rear support bar
63
reposition the center pantry drawer slide assembly
64
keeping the wires secured, reinstall the horizontal frame mullion assembly
65
rethread the screws
66
reconnect the wire connecters and replace the access cover
67
reconnect the vertical frame mullion wire connecter
68
make sure the tabs are straight then snap the frame into place
69
feed the crisper drawer support panel wire harness through the side housing as you reposition the support panel
70
connect the wire connecter and replace the cover
71
replace the pantry drawer fronts by first pushing up on the lever at the bottom of the glide bracket to open
72
insert the drawer front bracket into the glide bracket and release the lever to lock the drawer front in place
73
repeat for opposite side
74
reconnect the temperature control wire connecter on the left drawer and replace the cover
75
reposition the drawer bins
76
replace the storage tray
77
reposition the crisper drawers
78
realign the glass frame and replace the glass
79
replace the shelving
80
confirm the closing cam is properly set
81
with the hinge base parallel with the door, insert the hinge pin and bushing into the hole
82
rotate the hinge so the base is at a ninety degree angle to the door to reset the cam
83
realign both center hinges on the frame
84
thread the mounting screws to secure
85
make sure the hinge bushing and washer are intact
86
set each door on its respective bushing at a ninety degree angle and confirm it closes properly
87
reinstall the top hinge by inserting the wires and water line through the hole in the hinge
88
thread the mounting screws to secure
89
slide the bushing over the wires and water line and insert it into the hinge
90
connect the wire
91
thread the screw to secure the grounding wire
92
Water
93
reattach the water supply line
94
replace both hinge cover and secure them with the screws
95
Shock
96
plug the power cord back in
Applicable Product Model
Parts Needed
Damper Control Assembly
$104.58
Total$0.00
Related Articles & Videos
14:37
Part Replacement
KitchenAid 5 Door Refrigerator Evaporator Fan Motor Replacement W11087438
01:42
Part Replacement
KitchenAid 5 Door Refrigerator LED Light Assembly Replacement W10908166
09:31
Part Replacement
KitchenAid 5 Door Refrigerator Freezer Evaporator Fan Motor Replacement W11249952
12:07
Part Replacement
KitchenAid 5 Door Refrigerator Pantry Drawer Wire Harness Replacement W11170612
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com