Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Dishwasher Display Board Replacement (part 5304517591)
Frigidaire Dishwasher Display Board Replacement (part 5304517591)
Skill Level
Total Parts Cost
$63.64Estimated Savings
$112.5003:24
- Description
This video provides step-by-step repair instructions for replacing the display board on Frigidaire dishwasher model #FGID2466QF7A. The most common reason for replacing the display board is if the dishwasher won’t start.
All of the information for this display board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
All of the information for this display board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
Step By Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Display Board Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
Pull the retaining tab back to detach the old display board then disconnect the wire harness from the control board.
12
Install the new display board by aligning it in the control panel and snapping it into place.
13
Connect the wire harness to the control board.
14
Secure the wires under the retaining clip.
15
Position the wiring grommet in the control board cover then snap the cover into place.
16
Thread the two mounting screws.
17
Realign the control panel assembly and secure it with the screws.
18
Reinstall the outer door panel by aligning it on the inner panel then slide up.
19
Thread the four mounting screws to secure.
20
Turn the power supply back on.
21
Congrats! Your dishwasher is ready for use.
Description
This video provides step-by-step repair instructions for replacing the display board on Frigidaire dishwasher model #FGID2466QF7A. The most common reason for replacing the display board is if the dishwasher won’t start.
All of the information for this display board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
All of the information for this display board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
Step-By-Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Display Board Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
Pull the retaining tab back to detach the old display board then disconnect the wire harness from the control board.
12
Install the new display board by aligning it in the control panel and snapping it into place.
13
Connect the wire harness to the control board.
14
Secure the wires under the retaining clip.
15
Position the wiring grommet in the control board cover then snap the cover into place.
16
Thread the two mounting screws.
17
Realign the control panel assembly and secure it with the screws.
18
Reinstall the outer door panel by aligning it on the inner panel then slide up.
19
Thread the four mounting screws to secure.
20
Turn the power supply back on.
21
Congrats! Your dishwasher is ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com