Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairToro Snowblower Upper Chute Ring Retainer Replacement 108-4874-03
Toro Snowblower Upper Chute Ring Retainer Replacement 108-4874-03
Skill Level
Total Parts Cost
$7.77Estimated Savings
$112.5004:02
- Description
This video provides step-by-step repair instructions for replacing the upper chute ring retainer on a Toro snowblower.
All of the information for this drive belt replacement video is applicable to the following brands:
Toro
All of the information for this drive belt replacement video is applicable to the following brands:
Toro
Step By Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Upper Chute Ring Retainer Replacement
3
Tools Needed
4
You will need a 3/8th inch socket, a phillips-head screwdriver and pliers for this procedure.
5
Hot
6
Make sure the engine has cooled.
7
Use a 3/8th inch socket to unthread the three mounting bolts securing the chute handle and the chute itself.
8
Remove the assembly and detach the handle.
9
Using a phillips-head screwdriver, unthread the screw to release the chute ring seal.
10
Unthread the two front housing mounting screws.
11
Unthread the three screws from the right side of the housing.
12
Use the 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
13
Unthread the screws to release the two retaining clamps holding the housing to the handle, then fully remove the housing.
14
Use pliers to detach the ratchet pawl spring.
15
Unthread the four bolts to release the old ring retainer.
16
Before you install the new chute ring retainer, make sure the ratchet pawl is in place.
17
Align the retainer and thread the four bolts.
18
Reattach the ratchet pawl spring.
19
Reposition the housing.
20
Align the two retaining clamps and thread the screws to secure the housing to the handle.
21
Rethread the mounting bolt to secure the housing to the rear bracket.
22
Replace the three right-side screws.
23
Rethread the two screws securing the front of the housing.
24
Reposition the ring seal on the housing so the phillips-head screw hole aligns with the appropriate screw hole in the gear ring.
25
Thread the screw.
26
Realign the handle on the chute, then reposition the assembly on the ring seal and thread the three mounting bolts to secure.
27
Congrats! Your snowblower is ready for use.
Description
This video provides step-by-step repair instructions for replacing the upper chute ring retainer on a Toro snowblower.
All of the information for this drive belt replacement video is applicable to the following brands:
Toro
All of the information for this drive belt replacement video is applicable to the following brands:
Toro
Step-By-Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Upper Chute Ring Retainer Replacement
3
Tools Needed
4
You will need a 3/8th inch socket, a phillips-head screwdriver and pliers for this procedure.
5
Hot
6
Make sure the engine has cooled.
7
Use a 3/8th inch socket to unthread the three mounting bolts securing the chute handle and the chute itself.
8
Remove the assembly and detach the handle.
9
Using a phillips-head screwdriver, unthread the screw to release the chute ring seal.
10
Unthread the two front housing mounting screws.
11
Unthread the three screws from the right side of the housing.
12
Use the 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
13
Unthread the screws to release the two retaining clamps holding the housing to the handle, then fully remove the housing.
14
Use pliers to detach the ratchet pawl spring.
15
Unthread the four bolts to release the old ring retainer.
16
Before you install the new chute ring retainer, make sure the ratchet pawl is in place.
17
Align the retainer and thread the four bolts.
18
Reattach the ratchet pawl spring.
19
Reposition the housing.
20
Align the two retaining clamps and thread the screws to secure the housing to the handle.
21
Rethread the mounting bolt to secure the housing to the rear bracket.
22
Replace the three right-side screws.
23
Rethread the two screws securing the front of the housing.
24
Reposition the ring seal on the housing so the phillips-head screw hole aligns with the appropriate screw hole in the gear ring.
25
Thread the screw.
26
Realign the handle on the chute, then reposition the assembly on the ring seal and thread the three mounting bolts to secure.
27
Congrats! Your snowblower is ready for use.
Applicable Product Model
Parts Needed
Retainer
$7.77
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com