Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairToro Snowblower Auger Bearing Spacer Replacement 114-3781
Toro Snowblower Auger Bearing Spacer Replacement 114-3781
Skill Level
Total Parts Cost
$11.68Estimated Savings
$112.5004:18
- Description
This video provides step-by-step repair instructions for replacing the auger bearing spacer on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step By Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Auger Bearing Spacer Replacement
3
Tools Needed
4
"You will need a 3/8th inch socket, a 7/16th inch socket and a 9/16th inch socket for this procedure."
5
Use a 3/8th inch socket or nut driver to unthread the three mounting screws to release the belt cover.
6
Secure the auger and use a 7/16th inch socket to unthread the bolt securing the auger pulley.
7
Release the brake and remove the pulley and belt.
8
Unthread the screws securing the auger assembly.
9
Unthread the three screws on the right side of the auger housing.
10
Fully remove the auger assembly.
11
Use a 9/16th inch socket to unthread the bolt to release the bearing assembly.
12
Pull back the spacer tabs to release the flange and bearing.
13
Prepare the new auger bearing spacer for installation by transferring the washer from the old spacer to the new one.
14
Set the bearing into the new spacer and snap on the flange.
15
Make sure the washer is in place on the auger shaft then slide on the assembly.
16
Thread the bolt to secure.
17
"Reinstall the auger assembly by inserting the shaft through the hole in the left side of the housing, then align the assembly in on the right side of the housing."
18
Rethread the three screws.
19
Align the flange on the left side…then thread the screws.
20
"With the drive belt looped around the auger pulley, align the belt on the drive pulley and under the brake as you position the auger pulley on the shaft."
21
Slide on the washer then thread the bolt to secure the pulley.
22
"Confirm that the belt is seated properly, then replace the belt cover and secure it with the screws."
23
Congrats! Your snowblower is ready for use.
Description
This video provides step-by-step repair instructions for replacing the auger bearing spacer on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step-By-Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Auger Bearing Spacer Replacement
3
Tools Needed
4
"You will need a 3/8th inch socket, a 7/16th inch socket and a 9/16th inch socket for this procedure."
5
Use a 3/8th inch socket or nut driver to unthread the three mounting screws to release the belt cover.
6
Secure the auger and use a 7/16th inch socket to unthread the bolt securing the auger pulley.
7
Release the brake and remove the pulley and belt.
8
Unthread the screws securing the auger assembly.
9
Unthread the three screws on the right side of the auger housing.
10
Fully remove the auger assembly.
11
Use a 9/16th inch socket to unthread the bolt to release the bearing assembly.
12
Pull back the spacer tabs to release the flange and bearing.
13
Prepare the new auger bearing spacer for installation by transferring the washer from the old spacer to the new one.
14
Set the bearing into the new spacer and snap on the flange.
15
Make sure the washer is in place on the auger shaft then slide on the assembly.
16
Thread the bolt to secure.
17
"Reinstall the auger assembly by inserting the shaft through the hole in the left side of the housing, then align the assembly in on the right side of the housing."
18
Rethread the three screws.
19
Align the flange on the left side…then thread the screws.
20
"With the drive belt looped around the auger pulley, align the belt on the drive pulley and under the brake as you position the auger pulley on the shaft."
21
Slide on the washer then thread the bolt to secure the pulley.
22
"Confirm that the belt is seated properly, then replace the belt cover and secure it with the screws."
23
Congrats! Your snowblower is ready for use.
Applicable Product Model
Parts Needed
Spacer
$11.68
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com