Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairToro Snowblower Carburetor Repair Kit Replacement 127-9394
Toro Snowblower Carburetor Repair Kit Replacement 127-9394
Skill Level
Total Parts Cost
$34.48Estimated Savings
$112.5007:07
- Description
This video provides step-by-step repair instructions for replacing the carburetor repair kit on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step By Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Carburetor Repair Kit Installation
3
Tools Needed
4
You will need an 8mm socket, a 8mm wrench, a 3/8th inch socket, a half-inch socket, a 10mm socket and carburetor cleaner for this procedure.
5
Hot
6
Make sure the engine has cooled.
7
Spill
8
Be sure to perform this procedure with little or no fuel in the tank.
9
Use an 8mm socket to unthread five of the six bolts securing the muffler cover.
10
Use a 8mm wrench to unthread the sixth bolt.
11
Use a 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
12
Unthread the screws to release the two retaining clamps holding the housing to the handle.
13
Use a half-inch socket to fully unthread the upper bolts securing the handle assembly.
14
Sharp
15
Lower the handle to fully remove the muffler cover.
16
Spill
17
Detach the primer hose from the carburetor ? be prepared for some fuel to spill.
18
Disconnect the wires from the key switch terminals.
19
Use a 10mm socket to unthread the nuts securing the control housing.
20
Pull the housing off of the mounting bolts.
21
Slide off the carburetor intake gasket.
22
Spill
23
Attach a pinch clamp to the fuel line, then release the fuel line from the carburetor.
24
Pull the carburetor forward enough to detach the throttle rod.
25
Detach the throttle spring and you can fully remove the carburetor.
26
Use the 10mm socket to unthread the bottom screw to release the carburetor bowl.
27
Slide out the pin to remove the float and needle assembly.
28
Before you install the new carburetor repair kit components, it is recommended to use carburetor cleaner to clean out the carburetor ports.
29
Align the spring on the needle, then position the needle on the float.
30
Align the needle and float on the carburetor, then insert the pin to hold the assembly in place.
31
Position the bowl gasket and bowl, keeping the drain screw facing toward the primer hose inlet port.
32
Align the new gasket on the screw, then thread the screw to secure the bowl.
33
Confirm the outlet gasket is in place next to the insulator, then slide the carburetor back onto the bolts.
34
Reattach the throttle spring and rod to the carburetor.
35
Attach the fuel line, then remove the pinch clamp.
36
Slide the intake gasket onto the mounting bolts.
37
Reposition the control housing, then thread and tighten the mounting nuts.
38
Connect the wires to the key switch terminals.
39
Reattach the primer hose to the carburetor.
40
Reposition the muffler cover, and thread the six bolts to secure.
41
Reposition the handle assembly and rethread the upper bolts.
42
Align the two retaining clamps and thread the screws to secure the housing to the handle.
43
Rethread the mounting bolt to secure the housing to the rear bracket.
44
Refill the fuel tank if necessary.
45
Congrats! Your snowblower is ready for use.
Description
This video provides step-by-step repair instructions for replacing the carburetor repair kit on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step-By-Step Instructions
1
Toro Snowblower - Model 38752
2
Snowblower Carburetor Repair Kit Installation
3
Tools Needed
4
You will need an 8mm socket, a 8mm wrench, a 3/8th inch socket, a half-inch socket, a 10mm socket and carburetor cleaner for this procedure.
5
Hot
6
Make sure the engine has cooled.
7
Spill
8
Be sure to perform this procedure with little or no fuel in the tank.
9
Use an 8mm socket to unthread five of the six bolts securing the muffler cover.
10
Use a 8mm wrench to unthread the sixth bolt.
11
Use a 3/8th inch socket or nut driver to unthread the mounting bolt securing the housing to the rear bracket.
12
Unthread the screws to release the two retaining clamps holding the housing to the handle.
13
Use a half-inch socket to fully unthread the upper bolts securing the handle assembly.
14
Sharp
15
Lower the handle to fully remove the muffler cover.
16
Spill
17
Detach the primer hose from the carburetor ? be prepared for some fuel to spill.
18
Disconnect the wires from the key switch terminals.
19
Use a 10mm socket to unthread the nuts securing the control housing.
20
Pull the housing off of the mounting bolts.
21
Slide off the carburetor intake gasket.
22
Spill
23
Attach a pinch clamp to the fuel line, then release the fuel line from the carburetor.
24
Pull the carburetor forward enough to detach the throttle rod.
25
Detach the throttle spring and you can fully remove the carburetor.
26
Use the 10mm socket to unthread the bottom screw to release the carburetor bowl.
27
Slide out the pin to remove the float and needle assembly.
28
Before you install the new carburetor repair kit components, it is recommended to use carburetor cleaner to clean out the carburetor ports.
29
Align the spring on the needle, then position the needle on the float.
30
Align the needle and float on the carburetor, then insert the pin to hold the assembly in place.
31
Position the bowl gasket and bowl, keeping the drain screw facing toward the primer hose inlet port.
32
Align the new gasket on the screw, then thread the screw to secure the bowl.
33
Confirm the outlet gasket is in place next to the insulator, then slide the carburetor back onto the bolts.
34
Reattach the throttle spring and rod to the carburetor.
35
Attach the fuel line, then remove the pinch clamp.
36
Slide the intake gasket onto the mounting bolts.
37
Reposition the control housing, then thread and tighten the mounting nuts.
38
Connect the wires to the key switch terminals.
39
Reattach the primer hose to the carburetor.
40
Reposition the muffler cover, and thread the six bolts to secure.
41
Reposition the handle assembly and rethread the upper bolts.
42
Align the two retaining clamps and thread the screws to secure the housing to the handle.
43
Rethread the mounting bolt to secure the housing to the rear bracket.
44
Refill the fuel tank if necessary.
45
Congrats! Your snowblower is ready for use.
Applicable Product Model
Parts Needed
Carburetor Repair Kit
$34.48
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com