Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairToro Snowblower Carburetor Intake Gasket Replacement 121-0080
Toro Snowblower Carburetor Intake Gasket Replacement 121-0080
Skill Level
Total Parts Cost
$7.82Estimated Savings
$112.5004:24
- Description
This video provides step-by-step repair instructions for replacing the carburetor intake gasket on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step By Step Instructions
1
Before you replace the carburetor intake gasket in your snowblower, make sure the engine has cooled.
2
You can use an eight millimeter socket to unthread five of the six bolts securing the muffler cover.
3
You will need to use an 8 millimeter wrench to unthread the sixth bolt.
4
Use a 3/8 inch socket or nut driver to unthread the mounting bolts securing the housing to the rear bracket.
5
Next, unthread the screws to release the two retaining clamps holding the housing to the handle.
6
Now, use a half-inch socket to fully unfold securing the handle assembly.
7
Lower the handle and you can fully remove the muffler cover.
8
Detach the primer hose from the carburetor.
9
Be prepared for some fuel to spill.
10
Disconnect the wires from the key switch terminals.
11
Use a 10 millimeter socket to unthread the nuts securing the control housing.
12
Pull the housing off of the mounting bolts.
13
You can now slide off the old intake gasket if still intact.
14
Install the new carburetor intake gasket by sliding it onto the mounting bolts.
15
Reposition the control housing, then thread and tighten the mounting nuts.
16
Connect the wires to the key switch terminals.
17
Attach the primer hose to the carburetor.
18
Reposition the muffler cover and thread the six bolts to secure.
19
Reposition the handle assembly and rethread the upper bolts.
20
Align the two retaining clamps and thread the screws to secure the housing to the handle.
21
Rethread the mounting bolt to secure the housing to the rear bracket.
22
Your snowblower should now be ready for use.
Description
This video provides step-by-step repair instructions for replacing the carburetor intake gasket on a Toro snowblower.
All of the information for this video is applicable to the following brands:
Toro
All of the information for this video is applicable to the following brands:
Toro
Step-By-Step Instructions
1
Before you replace the carburetor intake gasket in your snowblower, make sure the engine has cooled.
2
You can use an eight millimeter socket to unthread five of the six bolts securing the muffler cover.
3
You will need to use an 8 millimeter wrench to unthread the sixth bolt.
4
Use a 3/8 inch socket or nut driver to unthread the mounting bolts securing the housing to the rear bracket.
5
Next, unthread the screws to release the two retaining clamps holding the housing to the handle.
6
Now, use a half-inch socket to fully unfold securing the handle assembly.
7
Lower the handle and you can fully remove the muffler cover.
8
Detach the primer hose from the carburetor.
9
Be prepared for some fuel to spill.
10
Disconnect the wires from the key switch terminals.
11
Use a 10 millimeter socket to unthread the nuts securing the control housing.
12
Pull the housing off of the mounting bolts.
13
You can now slide off the old intake gasket if still intact.
14
Install the new carburetor intake gasket by sliding it onto the mounting bolts.
15
Reposition the control housing, then thread and tighten the mounting nuts.
16
Connect the wires to the key switch terminals.
17
Attach the primer hose to the carburetor.
18
Reposition the muffler cover and thread the six bolts to secure.
19
Reposition the handle assembly and rethread the upper bolts.
20
Align the two retaining clamps and thread the screws to secure the housing to the handle.
21
Rethread the mounting bolt to secure the housing to the rear bracket.
22
Your snowblower should now be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com