Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Electric Laundry Center Washer User Interface Board Replacement (5304523182) 
Frigidaire Electric Laundry Center Washer User Interface Board Replacement (5304523182)
Skill Level
Total Parts Cost
$160.37Estimated Savings
$112.5004:41
- Description
This video provides step-by-step repair instructions for replacing the washer user interface board on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the washer buttons are not responding.
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the washer’s user interface board in your frigidaire laundry center…
2
… you will need a number two square drive bit, a phillips-head screwdriver, a small flat-head screwdriver, and needle-nose pliers.
3
Before you begin the procedure, unplug the power cord.
4
Use the number two square drive bit or the phillips-head screwdriver to unthread the two screws securing the dryer’s lower access panel.
5
Pull the panel up to remove.
6
Next, unthread the two mounting screws securing the control panel.
7
Pull the panel down to detach.
8
Release the wires from the retaining clip and set the panel on a towel or blanket.
9
Use the phillips-head screwdriver to unthread the four mounting screws securing the washer’s user interface board.
10
Pull off the selector knob.
11
You can now pull the retaining tabs back to release the board.
12
Depress the tab to disconnect the jumper wire harness…
13
… as well as the main wire harness.
14
Use the small flat-head screwdriver and needle-nose pliers to detach the wire retainers…
15
… and you can fully remove the old component.
16
To install the new user interface board…
17
… first connect the main wire harness connecter and the jumper wire harness connecter to the board.
18
Snap the wire retainers into place.
19
Align the new interface board and snap it into place.
20
Rethread the four screws to secure.
21
Replace the selector knob.
22
Secure the wires in the retaining clip…
23
… then reposition the control panel.
24
Replace the mounting screws.
25
Realign the access panel…
26
… and secure it with the screws.
27
Plug the power cord back in…
28
… and your laundry center should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the washer user interface board on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the washer buttons are not responding.
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the washer’s user interface board in your frigidaire laundry center…
2
… you will need a number two square drive bit, a phillips-head screwdriver, a small flat-head screwdriver, and needle-nose pliers.
3
Before you begin the procedure, unplug the power cord.
4
Use the number two square drive bit or the phillips-head screwdriver to unthread the two screws securing the dryer’s lower access panel.
5
Pull the panel up to remove.
6
Next, unthread the two mounting screws securing the control panel.
7
Pull the panel down to detach.
8
Release the wires from the retaining clip and set the panel on a towel or blanket.
9
Use the phillips-head screwdriver to unthread the four mounting screws securing the washer’s user interface board.
10
Pull off the selector knob.
11
You can now pull the retaining tabs back to release the board.
12
Depress the tab to disconnect the jumper wire harness…
13
… as well as the main wire harness.
14
Use the small flat-head screwdriver and needle-nose pliers to detach the wire retainers…
15
… and you can fully remove the old component.
16
To install the new user interface board…
17
… first connect the main wire harness connecter and the jumper wire harness connecter to the board.
18
Snap the wire retainers into place.
19
Align the new interface board and snap it into place.
20
Rethread the four screws to secure.
21
Replace the selector knob.
22
Secure the wires in the retaining clip…
23
… then reposition the control panel.
24
Replace the mounting screws.
25
Realign the access panel…
26
… and secure it with the screws.
27
Plug the power cord back in…
28
… and your laundry center should be ready for use.
Applicable Product Model
Parts Needed
Total$0.00
Related Articles & Videos
07:04
Part Replacement
Frigidaire Electric Laundry Center Dryer Drum Belt Replacement (134503600)
10:24
Part Replacement
Frigidaire Electric Laundry Center Heater Assembly Replacement (137392702)
09:35
Part Replacement
Frigidaire Electric Laundry Center Dryer Drum Bearing Replacement (131777700)
18:36
Part Replacement
Frigidaire Laundry Center Washer Transmission Assembly Replacement (5304517318)
04:37
Part Replacement
Frigidaire Laundry Center Water Inlet Valve Replacement (5304515818)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com