Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Laundry Center Washer Valve-to-Tub Fill Hose Replacement (5304508358)
Frigidaire Laundry Center Washer Valve-to-Tub Fill Hose Replacement (5304508358)
Skill Level
Total Parts Cost
$28.91Estimated Savings
$112.5005:40
- Description
This video provides step-by-step repair instructions for replacing the washer valve-to-tube fill hose on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the washer is not filling properly.
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the washer’s valve-to-tub fill hose in your frigidaire laundry center…
2
… you will need a number two square drive bit, a short phillips-head screwdriver, and pliers.
3
Before you begin the procedure, unplug the power cord…
4
… and shut off the incoming water supply.
5
Have an assistant help you to move the appliance away from the wall or out of the closet.
6
You may need to detach the venting from the dryer to fully access the rear of the laundry center.
7
If necessary, remove the drain hose from the standpipe or laundry tub.
8
If you haven’t already detached the hot and cold-water supply lines to move the appliance, unthread them from the water inlet valve ports – be prepared for some water to spill.
9
Now use the number two square drive bit or the phillips-head screwdriver to unthread the screw securing the inlet valve to the rear panel.
10
Push the valve in to detach it from the panel.
11
Next, from the front of the appliance…
12
… use the putty knife to release the two retaining clips securing the washer’s main top.
13
Lift up the top and disconnect the lid lock assembly wire connecter.
14
You can now fully remove the main top.
15
Reach into the cabinet to retrieve the inlet valve.
16
Use the pliers to release the spring clamp so you can detach the fill hose from the valve.
17
Next, unthread the two screws securing the dryer’s lower access panel.
18
Pull the panel up to remove.
19
Now use the short phillips-head screwdriver to unthread the screw securing the fill hose to the support panel.
20
Release the retaining tab to detach the hose from the panel then detach the hose from the retaining bracket to fully remove.
21
To prepare the new valve-to-tub fill hose for installation…
22
… transfer the spring clamp from the old hose to the new one.
23
Now snap the hose into place in the retaining bracket.
24
Hook the hose on the support panel then push the retaining tab into place.
25
Thread the screw to secure.
26
Realign the access panel…
27
… and secure it with the screws.
28
Attach the new fill hose to the inlet valve and secure it with the spring clamp.
29
Reposition the valve by inserting the ports through the hole in the rear panel.
30
Reinstall the main top by first reconnecting the lid lock assembly wire connecter.
31
Secure the wire in the retaining clip.
32
Now slide the rear of the main top under the rear retaining clips…
33
… then realign the main top and push down to snap it into position.
34
Returning to the rear of the appliance…
35
… thread the screw to secure the inlet valve to the rear panel.
36
Attach the hot and cold-water supply lines to the inlet valve ports.
37
If necessary, reinsert the drain hose into the standpipe or hook it onto the edge of the tub.
38
Reattach the venting if required…
39
… and move the appliance back against the wall or into the closet.
40
Turn the water supply back on…
41
… plug the power cord back in…
42
… and your laundry center should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the washer valve-to-tube fill hose on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the washer is not filling properly.
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Frigidaire
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the washer’s valve-to-tub fill hose in your frigidaire laundry center…
2
… you will need a number two square drive bit, a short phillips-head screwdriver, and pliers.
3
Before you begin the procedure, unplug the power cord…
4
… and shut off the incoming water supply.
5
Have an assistant help you to move the appliance away from the wall or out of the closet.
6
You may need to detach the venting from the dryer to fully access the rear of the laundry center.
7
If necessary, remove the drain hose from the standpipe or laundry tub.
8
If you haven’t already detached the hot and cold-water supply lines to move the appliance, unthread them from the water inlet valve ports – be prepared for some water to spill.
9
Now use the number two square drive bit or the phillips-head screwdriver to unthread the screw securing the inlet valve to the rear panel.
10
Push the valve in to detach it from the panel.
11
Next, from the front of the appliance…
12
… use the putty knife to release the two retaining clips securing the washer’s main top.
13
Lift up the top and disconnect the lid lock assembly wire connecter.
14
You can now fully remove the main top.
15
Reach into the cabinet to retrieve the inlet valve.
16
Use the pliers to release the spring clamp so you can detach the fill hose from the valve.
17
Next, unthread the two screws securing the dryer’s lower access panel.
18
Pull the panel up to remove.
19
Now use the short phillips-head screwdriver to unthread the screw securing the fill hose to the support panel.
20
Release the retaining tab to detach the hose from the panel then detach the hose from the retaining bracket to fully remove.
21
To prepare the new valve-to-tub fill hose for installation…
22
… transfer the spring clamp from the old hose to the new one.
23
Now snap the hose into place in the retaining bracket.
24
Hook the hose on the support panel then push the retaining tab into place.
25
Thread the screw to secure.
26
Realign the access panel…
27
… and secure it with the screws.
28
Attach the new fill hose to the inlet valve and secure it with the spring clamp.
29
Reposition the valve by inserting the ports through the hole in the rear panel.
30
Reinstall the main top by first reconnecting the lid lock assembly wire connecter.
31
Secure the wire in the retaining clip.
32
Now slide the rear of the main top under the rear retaining clips…
33
… then realign the main top and push down to snap it into position.
34
Returning to the rear of the appliance…
35
… thread the screw to secure the inlet valve to the rear panel.
36
Attach the hot and cold-water supply lines to the inlet valve ports.
37
If necessary, reinsert the drain hose into the standpipe or hook it onto the edge of the tub.
38
Reattach the venting if required…
39
… and move the appliance back against the wall or into the closet.
40
Turn the water supply back on…
41
… plug the power cord back in…
42
… and your laundry center should be ready for use.
Applicable Product Model
Parts Needed
Hose
$28.91
Total$0.00
Related Articles & Videos
07:04
Part Replacement
Frigidaire Electric Laundry Center Dryer Drum Belt Replacement (134503600)
10:24
Part Replacement
Frigidaire Electric Laundry Center Heater Assembly Replacement (137392702)
09:35
Part Replacement
Frigidaire Electric Laundry Center Dryer Drum Bearing Replacement (131777700)
18:36
Part Replacement
Frigidaire Laundry Center Washer Transmission Assembly Replacement (5304517318)
04:37
Part Replacement
Frigidaire Laundry Center Water Inlet Valve Replacement (5304515818)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com