Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Air Conditioner Turbo Fan Blade Replacement 5901A20009A 
LG Air Conditioner Turbo Fan Blade Replacement 5901A20009A
Skill Level
Total Parts Cost
$50.93Estimated Savings
$112.5007:16
- Description
This video provides step-by-step instructions for replacing the turbo fan blade on an LG Air Conditioner. The most common reason for replacing this part is if it is damaged or the air conditioner is noisy.
All of the information in this video is applicable to the following brands: LG
All of the information in this video is applicable to the following brands: LG
Step By Step Instructions
1
To replace the turbo fan blade in this lg built-in air conditioner…
2
… you will need a phillips-head screwdriver, a short phillips-head screwdriver, and pliers.
3
Before you begin the procedure, unplug the unit’s power cord.
4
Remove the inlet cover by detaching it from the top first.
5
Pull the air filter up and out.
6
Use the phillips-head screwdriver to unthread the two mounting screws securing the front grille assembly.
7
Pull the assembly out from the bottom then lift up to detach.
8
Disconnect the wire connecter to fully remove the assembly.
9
If required, use the phillips-head screwdriver to unthread the two rear mounting screws securing the unit to its cabinet.
10
Unthread the two front screws located on the left and right sides of the cabinet near the bottom.
11
Now have an assistant help you to fully remove the unit from the cabinet…
12
… and set it on a towel or blanket.
13
Next, unthread the two screws securing the service box cover.
14
Slide the cover forward and up to remove.
15
Detach the thermistor wires from the venting retaining clips.
16
Now move the service box out of the way so you can unthread the screw securing the venting.
17
Unthread the left-side screw securing the venting… and move the venting out of the way.
18
Unthread the two left-side screws securing the blower housing to the evaporator.
19
Unthread the right-side screw.
20
Carefully pull the evaporator forward.
21
Use the short phillips-head screwdriver to unthread the two right-side screws securing the front blower housing cover.
22
Pull the left-side retaining tab outward to fully detach the cover.
23
Use the pliers to remove the retaining clamp securing the turbo fan blade.
24
You can now slide the old fan blade off the motor shaft.
25
To install the new turbo fan blade…
26
… slide it onto the motor shaft…
27
… and replace the retaining clamp to secure.
28
Reposition the blower housing cover and snap the left-side retaining tab into place.
29
Rethread the two screws on the right to fully secure.
30
Carefully reposition the evaporator.
31
Thread the right-side screw to secure the evaporator to the blower housing.
32
Thread the two left-side screws as well.
33
Realign the venting…
34
… and thread the left-side screw.
35
Thread the right-side screw to fully secure the venting…
36
… then reposition the service box… and secure the two thermistor wires in the venting retaining clips.
37
Align the service box cover tabs with the slots and push the cover back.
38
Rethread the two mounting screws.
39
Now slide the air conditioning unit back into the cabinet.
40
Rethread the front screws on the left and right sides to secure.
41
Securing the unit with the rear cabinet screws is optional.
42
Reinstall the front grille assembly by first connecting the wire connecter.
43
Make sure the vent lever is accessible just below the horizontal louver as you insert the upper tabs into the slots in the frame, then position and snap the sides of the grille into place.
44
Rethread the two mounting screws to secure.
45
Realign the air filter by positioning the bottom edge first then snap the top of the filter into place.
46
Align the inlet cover hinge tabs with the slots in the grille assembly then snap the top portion of the cover into position.
47
Plug the power cord back in…
48
… and the air conditioner should be ready for use.
Description
This video provides step-by-step instructions for replacing the turbo fan blade on an LG Air Conditioner. The most common reason for replacing this part is if it is damaged or the air conditioner is noisy.
All of the information in this video is applicable to the following brands: LG
All of the information in this video is applicable to the following brands: LG
Step-By-Step Instructions
1
To replace the turbo fan blade in this lg built-in air conditioner…
2
… you will need a phillips-head screwdriver, a short phillips-head screwdriver, and pliers.
3
Before you begin the procedure, unplug the unit’s power cord.
4
Remove the inlet cover by detaching it from the top first.
5
Pull the air filter up and out.
6
Use the phillips-head screwdriver to unthread the two mounting screws securing the front grille assembly.
7
Pull the assembly out from the bottom then lift up to detach.
8
Disconnect the wire connecter to fully remove the assembly.
9
If required, use the phillips-head screwdriver to unthread the two rear mounting screws securing the unit to its cabinet.
10
Unthread the two front screws located on the left and right sides of the cabinet near the bottom.
11
Now have an assistant help you to fully remove the unit from the cabinet…
12
… and set it on a towel or blanket.
13
Next, unthread the two screws securing the service box cover.
14
Slide the cover forward and up to remove.
15
Detach the thermistor wires from the venting retaining clips.
16
Now move the service box out of the way so you can unthread the screw securing the venting.
17
Unthread the left-side screw securing the venting… and move the venting out of the way.
18
Unthread the two left-side screws securing the blower housing to the evaporator.
19
Unthread the right-side screw.
20
Carefully pull the evaporator forward.
21
Use the short phillips-head screwdriver to unthread the two right-side screws securing the front blower housing cover.
22
Pull the left-side retaining tab outward to fully detach the cover.
23
Use the pliers to remove the retaining clamp securing the turbo fan blade.
24
You can now slide the old fan blade off the motor shaft.
25
To install the new turbo fan blade…
26
… slide it onto the motor shaft…
27
… and replace the retaining clamp to secure.
28
Reposition the blower housing cover and snap the left-side retaining tab into place.
29
Rethread the two screws on the right to fully secure.
30
Carefully reposition the evaporator.
31
Thread the right-side screw to secure the evaporator to the blower housing.
32
Thread the two left-side screws as well.
33
Realign the venting…
34
… and thread the left-side screw.
35
Thread the right-side screw to fully secure the venting…
36
… then reposition the service box… and secure the two thermistor wires in the venting retaining clips.
37
Align the service box cover tabs with the slots and push the cover back.
38
Rethread the two mounting screws.
39
Now slide the air conditioning unit back into the cabinet.
40
Rethread the front screws on the left and right sides to secure.
41
Securing the unit with the rear cabinet screws is optional.
42
Reinstall the front grille assembly by first connecting the wire connecter.
43
Make sure the vent lever is accessible just below the horizontal louver as you insert the upper tabs into the slots in the frame, then position and snap the sides of the grille into place.
44
Rethread the two mounting screws to secure.
45
Realign the air filter by positioning the bottom edge first then snap the top of the filter into place.
46
Align the inlet cover hinge tabs with the slots in the grille assembly then snap the top portion of the cover into position.
47
Plug the power cord back in…
48
… and the air conditioner should be ready for use.
Applicable Product Model
Parts Needed
Blower Wheel
$50.93
Total$0.00
Related Articles & Videos
03:47
Part Replacement
LG Air Conditioner Vertical Louver Fin with Lever Replacement MFH63483702
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com