Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dryer High-Limit Thermostat Replacement #WE4M137
GE Dryer High-Limit Thermostat Replacement #WE4M137
Skill Level
Total Parts Cost
$74.08Estimated Savings
$112.5003:42
- Description
This video provides step-by-step instructions for replacing the high-limit thermostat on GE gas dryers. The most common reason for replacing the high-limit thermostat is when the dryer doesn’t heat and testing the thermostat for continuity proves it is at fault.
All of the information in this thermostat replacement video is applicable to the following brands: GE, Hotpoint, RCA
All of the information in this thermostat replacement video is applicable to the following brands: GE, Hotpoint, RCA
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the rear of the control panel to release it.
3
Next, open the dryer door and remove the screws inside the door frame which secure the main top.
4
Carefully unhook the control panel tabs from the main top, then lift up the top and remove.
5
Uninstall the screws securing the front panel.
6
Now lift the front panel up and rotate it to the side.
7
Remove the screw or screws securing the sides of the cabinet to the support panel.
8
Now reach under the drum and push the idler pulley to release the tension on the belt.
9
Then unthread the belt from the pulley and motor shaft.
10
Use the belt to help lift out the drum.
11
Disconnect the wires from the old high-limit thermostat and remove the mounting screw to release the thermostat from the heating duct.
12
Install the new high-limit thermostat by positioning it on the top of the duct and securing the mounting screw.
13
Connect the wires to the new thermostat.
14
Replace the drum in the cabinet by aligning the drum shaft and bearing with the bearing retainer on the rear panel.
15
Reach under the drum and thread the belt onto the pulley and motor shaft in a zig-zag formation.
16
Now rotate the drum to help align the belt.
17
Replace the screw or screws securing the sides of the cabinet to the support panel.
18
Reposition the front panel by first aligning the tabs in the base with the slots in the panel.
19
Now lift up the drum and snap the front panel into place.
20
Secure the screws.
21
Replace the main top by aligning the slots in the top with the tabs on the frame.
22
Then reinstall the screws in the door frame to secure.
23
Reposition the control panel by inserting the tabs into the slots at the back of the main top.
24
Replace the screws in the back to secure.
25
You're now ready to plug the power cord back in and confirm that the appliance is functioning properly.
Description
This video provides step-by-step instructions for replacing the high-limit thermostat on GE gas dryers. The most common reason for replacing the high-limit thermostat is when the dryer doesn’t heat and testing the thermostat for continuity proves it is at fault.
All of the information in this thermostat replacement video is applicable to the following brands: GE, Hotpoint, RCA
All of the information in this thermostat replacement video is applicable to the following brands: GE, Hotpoint, RCA
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the rear of the control panel to release it.
3
Next, open the dryer door and remove the screws inside the door frame which secure the main top.
4
Carefully unhook the control panel tabs from the main top, then lift up the top and remove.
5
Uninstall the screws securing the front panel.
6
Now lift the front panel up and rotate it to the side.
7
Remove the screw or screws securing the sides of the cabinet to the support panel.
8
Now reach under the drum and push the idler pulley to release the tension on the belt.
9
Then unthread the belt from the pulley and motor shaft.
10
Use the belt to help lift out the drum.
11
Disconnect the wires from the old high-limit thermostat and remove the mounting screw to release the thermostat from the heating duct.
12
Install the new high-limit thermostat by positioning it on the top of the duct and securing the mounting screw.
13
Connect the wires to the new thermostat.
14
Replace the drum in the cabinet by aligning the drum shaft and bearing with the bearing retainer on the rear panel.
15
Reach under the drum and thread the belt onto the pulley and motor shaft in a zig-zag formation.
16
Now rotate the drum to help align the belt.
17
Replace the screw or screws securing the sides of the cabinet to the support panel.
18
Reposition the front panel by first aligning the tabs in the base with the slots in the panel.
19
Now lift up the drum and snap the front panel into place.
20
Secure the screws.
21
Replace the main top by aligning the slots in the top with the tabs on the frame.
22
Then reinstall the screws in the door frame to secure.
23
Reposition the control panel by inserting the tabs into the slots at the back of the main top.
24
Replace the screws in the back to secure.
25
You're now ready to plug the power cord back in and confirm that the appliance is functioning properly.
Applicable Product Model
Parts Needed
High Limit Thermostat
$74.08
Recommended Tools and Accessories
Cooktop Cleaner
$29.50
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com