Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dryer Cycling Thermostat Replacement #WE4M216
GE Dryer Cycling Thermostat Replacement #WE4M216
Skill Level
Total Parts Cost
$89.21Estimated Savings
$112.5003:44
- Description
This video provides step-by-step repair instructions for replacing the cycling thermostat on a GE gas dryer. The most common reasons for replacing the cycling thermostat are when the dryer doesn’t heat, is too hot, takes too long, or won’t stop.
All of the information for this cycling thermostat replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
All of the information for this cycling thermostat replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the rear of the control panel to release it.
3
Next, open the dryer door and remove the screws inside the door frame which secure the main top.
4
Now carefully slide the main top forward, unhook it from the control panel tabs and remove.
5
Uninstall the screws securing the front panel.
6
Now, lift the front panel up and rotate it to the side.
7
Remove the screw or screws securing the sides of the cabinet to the support panel.
8
Now reach under the drum and push the idler pulley to release the tension on the belt then unthread the belt from the pulley and motor shaft.
9
Use the belt to help lift out the drum.
10
Next, remove the mounting screw securing the old cycling thermostat and pull the thermostat away from the blower housing.
11
Install the new cycling thermostat by positioning it on the blower housing and securing the mounting screw.
12
Now transfer the wires from the old thermostat to the new one.
13
Replace the drum in the cabinet by aligning the drum shaft and bearing with the bearing retainer on the rear panel.
14
Reach under the drum and thread the belt onto the pulley and motor shaft in a zig-zag formation.
15
Now, rotate the drum to help align the belt.
16
Replace the screw or screws securing the sides of the cabinet to the support panel.
17
Reposition the front panel by first inserting the tabs in the base with the slots in the panel.
18
Now lift up the drum and snap the front panel into place.
19
Secure the screws.
20
Replace the 23main top by inserting the control panel tabs into the slots at the back of the main top.
21
Fully position then replace the screws.
22
Secure the control panel with the screws in the back.
23
You’re now ready to plug the power cord back in and confirm that the appliance is functioning properly.
Description
This video provides step-by-step repair instructions for replacing the cycling thermostat on a GE gas dryer. The most common reasons for replacing the cycling thermostat are when the dryer doesn’t heat, is too hot, takes too long, or won’t stop.
All of the information for this cycling thermostat replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
All of the information for this cycling thermostat replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the rear of the control panel to release it.
3
Next, open the dryer door and remove the screws inside the door frame which secure the main top.
4
Now carefully slide the main top forward, unhook it from the control panel tabs and remove.
5
Uninstall the screws securing the front panel.
6
Now, lift the front panel up and rotate it to the side.
7
Remove the screw or screws securing the sides of the cabinet to the support panel.
8
Now reach under the drum and push the idler pulley to release the tension on the belt then unthread the belt from the pulley and motor shaft.
9
Use the belt to help lift out the drum.
10
Next, remove the mounting screw securing the old cycling thermostat and pull the thermostat away from the blower housing.
11
Install the new cycling thermostat by positioning it on the blower housing and securing the mounting screw.
12
Now transfer the wires from the old thermostat to the new one.
13
Replace the drum in the cabinet by aligning the drum shaft and bearing with the bearing retainer on the rear panel.
14
Reach under the drum and thread the belt onto the pulley and motor shaft in a zig-zag formation.
15
Now, rotate the drum to help align the belt.
16
Replace the screw or screws securing the sides of the cabinet to the support panel.
17
Reposition the front panel by first inserting the tabs in the base with the slots in the panel.
18
Now lift up the drum and snap the front panel into place.
19
Secure the screws.
20
Replace the 23main top by inserting the control panel tabs into the slots at the back of the main top.
21
Fully position then replace the screws.
22
Secure the control panel with the screws in the back.
23
You’re now ready to plug the power cord back in and confirm that the appliance is functioning properly.
Applicable Product Model
Parts Needed
Cycling Thermostat
$89.21
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com