Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Top-Load Washer Tub Cover Assembly #WH49X21274
GE Top-Load Washer Tub Cover Assembly #WH49X21274
Skill Level
Total Parts Cost
$154.42Estimated Savings
$112.5005:01
- Description
This video provides step-by-step repair instructions for replacing the tub cover assembly on a GE top-loading washing machine. The most common reason for replacing the tub cover is when it is broken and clothes are getting stuck between the inner and outer washer tubs.
All of the information for this tub cover assembly replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
All of the information for this tub cover assembly replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning
2
Turn off the hot and cold water supply valves.
3
Your first step is to disconnect the water supply hoses from the inlet valve.
4
Be prepared for some water to spill out.
5
Next, remove the screws at the back of the control panel.
6
Slide the panel to the side to detach it from the main top.
7
Detach the wires from the control board and set the control panel aside.
8
Now, insert a putty knife under the main top to release the two spring clips securing the front panel.
9
Pull the front panel forward and lift up to remove.
10
Next, remove the two screws securing the main top.
11
Slide the main top forward slightly, lift up and use pliers to squeeze the lid switch wire retainer to release it from the frame.
12
Now lift up the lid squeeze the tab to release the lid switch and pull it through the opening in the main top.
13
You can now completely remove the top and set it aside.
14
Remove the screws to release the rear panel, the control panel bracket and trim
15
Use pliers to gently remove the air pressure tube from the pressure switch.
16
You can now move the control panel bracket out of the way.
17
Remove the screws securing the shock dampening straps and pull the straps from the old tub cover.
18
Release the tabs on the bottom of the tub cover and pull the old cover off.
19
Install the new tub cover
20
By aligning the tab slots in the cover with the tabs on the tub and snap the new cover into place.
21
Replace the shock dampening straps and secure with the screws.
22
Reposition the control panel bracket and reconnect the air pressure tube to the pressure switch.
23
Replace the control panel trim by inserting the trim tabs into the slots in the frame.
24
Reposition the rear panel and secure all of the screws.
25
Replace the main top by first inserting the lid switch through the hole in the top and snap it into place.
26
Snap the wire retainer into the frame.
27
Now align the slots in the main top with the mounting tabs on the frame and push the main top back into place.
28
Secure with the screws in the front.
29
Reposition the front panel by aligning the tabs on the base with the slots at the bottom of the panel.
30
Align the pins on the front of the cabinet with the holes in the front panel and snap the panel into position.
31
Reconnect the wires to the control board.
32
Insert the tabs on the bottom of the control panel into the slots in the main top and slide the panel to the side to lock it into place.
33
Replace the screws to secure the control panel.
34
Reconnect the water supply hoses to the inlet valve and turn the water supply back on.
35
You’re now ready to plug the power cord back in and confirm that the appliance is functioning properly.
Description
This video provides step-by-step repair instructions for replacing the tub cover assembly on a GE top-loading washing machine. The most common reason for replacing the tub cover is when it is broken and clothes are getting stuck between the inner and outer washer tubs.
All of the information for this tub cover assembly replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
All of the information for this tub cover assembly replacement video is applicable to the following brands:
GE, Hotpoint, RCA, Americana
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning
2
Turn off the hot and cold water supply valves.
3
Your first step is to disconnect the water supply hoses from the inlet valve.
4
Be prepared for some water to spill out.
5
Next, remove the screws at the back of the control panel.
6
Slide the panel to the side to detach it from the main top.
7
Detach the wires from the control board and set the control panel aside.
8
Now, insert a putty knife under the main top to release the two spring clips securing the front panel.
9
Pull the front panel forward and lift up to remove.
10
Next, remove the two screws securing the main top.
11
Slide the main top forward slightly, lift up and use pliers to squeeze the lid switch wire retainer to release it from the frame.
12
Now lift up the lid squeeze the tab to release the lid switch and pull it through the opening in the main top.
13
You can now completely remove the top and set it aside.
14
Remove the screws to release the rear panel, the control panel bracket and trim
15
Use pliers to gently remove the air pressure tube from the pressure switch.
16
You can now move the control panel bracket out of the way.
17
Remove the screws securing the shock dampening straps and pull the straps from the old tub cover.
18
Release the tabs on the bottom of the tub cover and pull the old cover off.
19
Install the new tub cover
20
By aligning the tab slots in the cover with the tabs on the tub and snap the new cover into place.
21
Replace the shock dampening straps and secure with the screws.
22
Reposition the control panel bracket and reconnect the air pressure tube to the pressure switch.
23
Replace the control panel trim by inserting the trim tabs into the slots in the frame.
24
Reposition the rear panel and secure all of the screws.
25
Replace the main top by first inserting the lid switch through the hole in the top and snap it into place.
26
Snap the wire retainer into the frame.
27
Now align the slots in the main top with the mounting tabs on the frame and push the main top back into place.
28
Secure with the screws in the front.
29
Reposition the front panel by aligning the tabs on the base with the slots at the bottom of the panel.
30
Align the pins on the front of the cabinet with the holes in the front panel and snap the panel into position.
31
Reconnect the wires to the control board.
32
Insert the tabs on the bottom of the control panel into the slots in the main top and slide the panel to the side to lock it into place.
33
Replace the screws to secure the control panel.
34
Reconnect the water supply hoses to the inlet valve and turn the water supply back on.
35
You’re now ready to plug the power cord back in and confirm that the appliance is functioning properly.
Applicable Product Model
Recommended Tools and Accessories
Cleaner
$7.62
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com