Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Top-Load Washer Main Control Board Replacement W11419051 
Whirlpool Top-Load Washer Main Control Board Replacement W11419051
Skill Level
Total Parts Cost
$262.25Estimated Savings
$112.5004:02
- Description
This video provides step-by-step instructions for replacing the main control board on a Whirlpool top-loading washing machine, model WTW7120HW0. The most common reason for replacing this part is if the washer will not work at all.
All of the information in this part replacement video is applicable to the following brands: Whirlpool
All of the information in this part replacement video is applicable to the following brands: Whirlpool
Step By Step Instructions
1
To replace the main control board in this whirlpool top-load washer…
2
… you will need a quarter-inch nut driver and a putty knife.
3
Before you begin the procedure, unplug the appliance’s power cord.
4
Have an assistant help you to move the washer away from the wall.
5
Use the quarter-inch nut driver to unthread the two rear screws securing the control panel assembly.
6
Next, insert a putty knife under the front corners of the control panel housing to release the clips securing the housing.
7
Disconnect the user interface control wire connecter so you can set the control panel assembly aside.
8
Note the orientation of the wires connected to the main control board…
9
… then disconnect them.
10
Detach the air pressure tube from the board as well.
11
Using the quarter-inch nut driver, unthread the screw securing the control board.
12
Release the wires from the retainers and you can remove the old board.
13
To install the new main control board…
14
… insert the side clips into the slot in the main top…
15
… then thread the screw to secure.
16
Secure the wiring under the retainers.
17
Connect the wire connecters to the appropriate terminals on the board.
18
Attach the air pressure tube as well.
19
Reconnect the user interface control wire connecter to the main control board.
20
Insert the rear control panel housing clips into the rear slots in the main top first… then snap the front clips into place.
21
Rethread the two rear screws to fully secure.
22
Move the washer back against the wall.
23
Plug the appliance’s power cord back in…
24
… and the washer should be ready for use.
Description
This video provides step-by-step instructions for replacing the main control board on a Whirlpool top-loading washing machine, model WTW7120HW0. The most common reason for replacing this part is if the washer will not work at all.
All of the information in this part replacement video is applicable to the following brands: Whirlpool
All of the information in this part replacement video is applicable to the following brands: Whirlpool
Step-By-Step Instructions
1
To replace the main control board in this whirlpool top-load washer…
2
… you will need a quarter-inch nut driver and a putty knife.
3
Before you begin the procedure, unplug the appliance’s power cord.
4
Have an assistant help you to move the washer away from the wall.
5
Use the quarter-inch nut driver to unthread the two rear screws securing the control panel assembly.
6
Next, insert a putty knife under the front corners of the control panel housing to release the clips securing the housing.
7
Disconnect the user interface control wire connecter so you can set the control panel assembly aside.
8
Note the orientation of the wires connected to the main control board…
9
… then disconnect them.
10
Detach the air pressure tube from the board as well.
11
Using the quarter-inch nut driver, unthread the screw securing the control board.
12
Release the wires from the retainers and you can remove the old board.
13
To install the new main control board…
14
… insert the side clips into the slot in the main top…
15
… then thread the screw to secure.
16
Secure the wiring under the retainers.
17
Connect the wire connecters to the appropriate terminals on the board.
18
Attach the air pressure tube as well.
19
Reconnect the user interface control wire connecter to the main control board.
20
Insert the rear control panel housing clips into the rear slots in the main top first… then snap the front clips into place.
21
Rethread the two rear screws to fully secure.
22
Move the washer back against the wall.
23
Plug the appliance’s power cord back in…
24
… and the washer should be ready for use.
Applicable Product Model
Parts Needed
Main Control Board
$262.25
Total$0.00
Related Articles & Videos
05:14
Part Replacement
Whirlpool Top-Load Washer Water Inlet Valve Replacement 218605101
05:41
Part Replacement
Whirlpool Top-Load Washer Lid Lock Assembly Replacement W11394572
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com