Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Drain Hose Assembly Replacement AEM74772903
This video provides step-by-step repair instructions for replacing the drain hose assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Drain Hose Assembly Replacement AEM74772903
Skill Level
Total Parts Cost
$75.94Estimated Savings
$112.5009:47
- Description
This video provides step-by-step repair instructions for replacing the drain hose assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the drain hose in your lg washer, you will need needle nose pliers, spring removal tool, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the two screws on the top panel.
6
Slide and lift the top panel off.
7
Unthread the screw securing the right side of the control panel.
8
Open the drawer and push down on the “push” tab and remove the detergent assembly.
9
Unthread the two screws that secure the left side of the control panel.
10
Pry the three tabs then pull back and lift up to free the control panel.
11
Unplug the harness to the control panel.
12
Open the drain clean-out door.
13
Use the pliers and squeeze the tabs at the hinges to remove the door.
14
Unclip the drain hose then unthread the two phillips screws.
15
Pull out the case.
16
Unthread the screw under the drain pump clean-out.
17
Insert the spring tool on either end of the spring,then pull to remove the ring.
18
Detach the boot seal from the front panel.
19
Unthread the two screws securing the door lock.
20
Unthread the six screws on the front panel.
21
Push the panel down to release it from the tab.
22
Unplug the door lock from the harness.
23
Lift the front panel up and away from the washer.
24
Slide the tension clamp back on the drain hose then disconncect the hose.
25
Remove the tension clamp.
26
Detatch the drain hose from the guides.
27
Unthread the four screws securing the rear cover.
28
Push the cover up and pull out to remove.
29
Unthread the screw securing the hose retaining clamp.
30
Remove the clamp.
31
Unhook the hose from the drain hose retaining clips.
32
Pull the hose out of the appliance.
33
To install the new drain hose, feed the hose through the washer.
34
Attach the tension clamp to the hose.
35
Secure the drain hose to the pump with the clamp.
36
Place the hose in the guides.
37
Snap the hose in the clips.
38
Clip the retaining clamp over the hose and fasten it to the washer.
39
Slide the rear cover into position.
40
Rethread the four screws.
41
Set the panel on the three tabs and plug in the door lock.
42
Push the panel upright and lock it in place with the tab.
43
Rethread the six screws into the panel.
44
Tuck the boot seal into the front panel.
45
Tuck the ring into the seal starting at the top.
46
Insert the spring removal tool into the ring to securely seat it into the seal.
47
Rethread the screw underneath the drain pump clean-out.
48
Feed the drain hose through the case and place in the washer.
49
Rethread the two phillips screws.
50
Clip in the drain hose.
51
Plug the wire harness back into the display board.
52
Insert the control panel into its grooves and push forward to snap in place…
53
Rethread the two screws on the left side of the control panel.
54
Align the detergent assembly and push in until it snaps into place.
55
Rethread the screw on the right side of the control panel.
56
Set and slide the top panel onto the washer.
57
Rethread the two screws into the panel.
58
Push the washer back into place.
59
Plug the power cord back in
60
Turn on the water supply, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain hose assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the drain hose assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the drain hose in your lg washer, you will need needle nose pliers, spring removal tool, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Unthread the two screws on the top panel.
6
Slide and lift the top panel off.
7
Unthread the screw securing the right side of the control panel.
8
Open the drawer and push down on the “push” tab and remove the detergent assembly.
9
Unthread the two screws that secure the left side of the control panel.
10
Pry the three tabs then pull back and lift up to free the control panel.
11
Unplug the harness to the control panel.
12
Open the drain clean-out door.
13
Use the pliers and squeeze the tabs at the hinges to remove the door.
14
Unclip the drain hose then unthread the two phillips screws.
15
Pull out the case.
16
Unthread the screw under the drain pump clean-out.
17
Insert the spring tool on either end of the spring,then pull to remove the ring.
18
Detach the boot seal from the front panel.
19
Unthread the two screws securing the door lock.
20
Unthread the six screws on the front panel.
21
Push the panel down to release it from the tab.
22
Unplug the door lock from the harness.
23
Lift the front panel up and away from the washer.
24
Slide the tension clamp back on the drain hose then disconncect the hose.
25
Remove the tension clamp.
26
Detatch the drain hose from the guides.
27
Unthread the four screws securing the rear cover.
28
Push the cover up and pull out to remove.
29
Unthread the screw securing the hose retaining clamp.
30
Remove the clamp.
31
Unhook the hose from the drain hose retaining clips.
32
Pull the hose out of the appliance.
33
To install the new drain hose, feed the hose through the washer.
34
Attach the tension clamp to the hose.
35
Secure the drain hose to the pump with the clamp.
36
Place the hose in the guides.
37
Snap the hose in the clips.
38
Clip the retaining clamp over the hose and fasten it to the washer.
39
Slide the rear cover into position.
40
Rethread the four screws.
41
Set the panel on the three tabs and plug in the door lock.
42
Push the panel upright and lock it in place with the tab.
43
Rethread the six screws into the panel.
44
Tuck the boot seal into the front panel.
45
Tuck the ring into the seal starting at the top.
46
Insert the spring removal tool into the ring to securely seat it into the seal.
47
Rethread the screw underneath the drain pump clean-out.
48
Feed the drain hose through the case and place in the washer.
49
Rethread the two phillips screws.
50
Clip in the drain hose.
51
Plug the wire harness back into the display board.
52
Insert the control panel into its grooves and push forward to snap in place…
53
Rethread the two screws on the left side of the control panel.
54
Align the detergent assembly and push in until it snaps into place.
55
Rethread the screw on the right side of the control panel.
56
Set and slide the top panel onto the washer.
57
Rethread the two screws into the panel.
58
Push the washer back into place.
59
Plug the power cord back in
60
Turn on the water supply, and your washer should be ready for use.
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com