Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Dishwasher Overfill Funnel Tube Replacement W11025988 
This video provides step-by-step repair instructions for replacing the overfill funnel tube on a KitchenAid dishwasher. The most common reason for replacing this part is if the dishwasher is leaking.
All of the information for this replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
KitchenAid Dishwasher Overfill Funnel Tube Replacement W11025988
Skill Level
Total Parts Cost
$18.00Estimated Savings
$112.5003:42
- Description
This video provides step-by-step repair instructions for replacing the overfill funnel tube on a KitchenAid dishwasher. The most common reason for replacing this part is if the dishwasher is leaking.
All of the information for this replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Step By Step Instructions
1
To replace an overfill funnel tube in this kitchenaid dishwasher, you will need a 5/16th inch nut driver and a small flat-head screwdriver.
2
Before you begin the procedure, turn off the power to the dishwasher.
3
Use the 5/16th inch nut driver to unthread the two screws securing the lower access panel and toe panel to the frame.
4
With the screws unthreaded, you can set the panels aside.
5
Pull out the remaining insulation.
6
Depress the side retaining clips so you can pull the drip tray forward.
7
Release the tabs and fully detach the float switch from the tray.
8
Depending on which tube you’re replacing, use the small flat-head screwdriver to depress the retaining tab to release the water inlet valve bracket or the junction box from the support bar and move it out of the way.
9
You can now pull the old tube off of the overfill funnel, if still intact.
10
To install the new overfill funnel tube, align it on the funnel port and push up until secure.
11
Realign the water inlet valve bracket or junction box on the support bar and snap it into position on the retaining tab – this may require some effort.
12
Partially reposition the drip tray and snap the switch into the tray.
13
Now fully reposition the tray, snapping it into place.
14
Realign the insulation.
15
Now realign the toe panel and insulation, then reposition the access panel, and thread the two screws to secure.
16
Turn the power supply back on, and the dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the overfill funnel tube on a KitchenAid dishwasher. The most common reason for replacing this part is if the dishwasher is leaking.
All of the information for this replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
This video provides step-by-step repair instructions for replacing the overfill funnel tube on a KitchenAid dishwasher. The most common reason for replacing this part is if the dishwasher is leaking.
All of the information for this replacement video is applicable to the following brands:
Kenmore, KitchenAid, Whirlpool, Ikea, Amana, Jenn Air, Maytag
Step-By-Step Instructions
1
To replace an overfill funnel tube in this kitchenaid dishwasher, you will need a 5/16th inch nut driver and a small flat-head screwdriver.
2
Before you begin the procedure, turn off the power to the dishwasher.
3
Use the 5/16th inch nut driver to unthread the two screws securing the lower access panel and toe panel to the frame.
4
With the screws unthreaded, you can set the panels aside.
5
Pull out the remaining insulation.
6
Depress the side retaining clips so you can pull the drip tray forward.
7
Release the tabs and fully detach the float switch from the tray.
8
Depending on which tube you’re replacing, use the small flat-head screwdriver to depress the retaining tab to release the water inlet valve bracket or the junction box from the support bar and move it out of the way.
9
You can now pull the old tube off of the overfill funnel, if still intact.
10
To install the new overfill funnel tube, align it on the funnel port and push up until secure.
11
Realign the water inlet valve bracket or junction box on the support bar and snap it into position on the retaining tab – this may require some effort.
12
Partially reposition the drip tray and snap the switch into the tray.
13
Now fully reposition the tray, snapping it into place.
14
Realign the insulation.
15
Now realign the toe panel and insulation, then reposition the access panel, and thread the two screws to secure.
16
Turn the power supply back on, and the dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com