Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dryer Duct Trap Felt Seal Replacement WE09X27634
This video provides step-by-step repair instructions for replacing the duct trap felt seal in a GE dryer (Model GTD42EASJ2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with dryer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Dryer Duct Trap Felt Seal Replacement WE09X27634
Skill Level
Total Parts Cost
$34.51Estimated Savings
$112.5013:10
- Description
This video provides step-by-step repair instructions for replacing the duct trap felt seal in a GE dryer (Model GTD42EASJ2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with dryer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the felt on the duct trap in your ge dryer, you will need a drill driver with a 1/4” bit, needlenose pliers, a #1 square head bit, a #2 square head bit.
2
Before you begin the procedure, unplug the power to the appliance.
3
Unthread the five screws on the panel. any missing screws can be ordered through the links in the description below.
4
Pull out and lift the panel from the backsplash.
5
Detatch the ground wire.
6
Unthread the two screws that secure the backsplash.
7
Pull the backsplash back, and lift up to free it from the dryer.
8
Note the orientation of the wires.
9
Detatch the purple, brown, and red wires from the start switch.
10
Now detatch the red wire from the signal switch.
11
Detatch the purple, brown, yellow, and red wires from the timer.
12
Detatch the blue, yellow, brown, and bottom orange wires from the temperature switch.
13
Detatch the brown wire from the extended tumble switch.
14
Detatch the brown and white wires from the resistor.
15
Unthread the two screws securing both the top panel plates.
16
Detatch the solid brown wire from the purple wire.
17
Feed the wires through the panel.
18
Unthread the two screws on the top of the panel, then unthread the two screws under the lip of the door threshold.
19
Lift the top panel from the appliance.
20
Unthread the two screws securing the front panel.
21
Pull the panel back and unplug the two wire harnesses.
22
Lift the panel off the three tabs, and move it to a flat surface.
23
Unthread the two panhead screws then flip the panel.
24
Pull back each side of the panel and lift out the assembly.
25
Peel out the felt.
26
To install the new felt, tuck the felt behind the tabs of the slide.
27
Pull back the sides of the panel and tuck each side of the assembly in until seated.
28
Flip the panel over and rethread the two panhead screws.
29
Set the front panel on the three tabs, then plug in the two wire hanresses.
30
Push the panel forward, then secure it with the two screws.
31
Set the panel on the appliance and feed the wires through.
32
Hook the back of the top panel and adjust it till it is aligned.
33
Rethread the two screws under the door threshold, as well as the two screws on the top of the panel.
34
Reattach the solid brown wire to the purple wire.
35
Slide the top plates into position and secure with the two screws.
36
Reattach the white and brown wires to the resistor.
37
Reattach the brown wire into the extended tumble switch.
38
Reattach the blue, yellow, brown, and bottom orange wires into the temperature switch.
39
Reattach the purple, brown, yellow, and red wires into the timer.
40
Reattach the red wire into the signal switch.
41
Reattach the purple, brown, and red wires to the start switch.
42
Set the backsplash back into the dryer slots and push forward to lock in place.
43
Rethread the two screws.
44
Reattach the ground wire to the panel.
45
Insert the panel tabs into the slots on the dryer.
46
Rethread the five screws.
47
Plug in the dryer, and your dryer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the duct trap felt seal in a GE dryer (Model GTD42EASJ2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with dryer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the duct trap felt seal in a GE dryer (Model GTD42EASJ2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with dryer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the felt on the duct trap in your ge dryer, you will need a drill driver with a 1/4” bit, needlenose pliers, a #1 square head bit, a #2 square head bit.
2
Before you begin the procedure, unplug the power to the appliance.
3
Unthread the five screws on the panel. any missing screws can be ordered through the links in the description below.
4
Pull out and lift the panel from the backsplash.
5
Detatch the ground wire.
6
Unthread the two screws that secure the backsplash.
7
Pull the backsplash back, and lift up to free it from the dryer.
8
Note the orientation of the wires.
9
Detatch the purple, brown, and red wires from the start switch.
10
Now detatch the red wire from the signal switch.
11
Detatch the purple, brown, yellow, and red wires from the timer.
12
Detatch the blue, yellow, brown, and bottom orange wires from the temperature switch.
13
Detatch the brown wire from the extended tumble switch.
14
Detatch the brown and white wires from the resistor.
15
Unthread the two screws securing both the top panel plates.
16
Detatch the solid brown wire from the purple wire.
17
Feed the wires through the panel.
18
Unthread the two screws on the top of the panel, then unthread the two screws under the lip of the door threshold.
19
Lift the top panel from the appliance.
20
Unthread the two screws securing the front panel.
21
Pull the panel back and unplug the two wire harnesses.
22
Lift the panel off the three tabs, and move it to a flat surface.
23
Unthread the two panhead screws then flip the panel.
24
Pull back each side of the panel and lift out the assembly.
25
Peel out the felt.
26
To install the new felt, tuck the felt behind the tabs of the slide.
27
Pull back the sides of the panel and tuck each side of the assembly in until seated.
28
Flip the panel over and rethread the two panhead screws.
29
Set the front panel on the three tabs, then plug in the two wire hanresses.
30
Push the panel forward, then secure it with the two screws.
31
Set the panel on the appliance and feed the wires through.
32
Hook the back of the top panel and adjust it till it is aligned.
33
Rethread the two screws under the door threshold, as well as the two screws on the top of the panel.
34
Reattach the solid brown wire to the purple wire.
35
Slide the top plates into position and secure with the two screws.
36
Reattach the white and brown wires to the resistor.
37
Reattach the brown wire into the extended tumble switch.
38
Reattach the blue, yellow, brown, and bottom orange wires into the temperature switch.
39
Reattach the purple, brown, yellow, and red wires into the timer.
40
Reattach the red wire into the signal switch.
41
Reattach the purple, brown, and red wires to the start switch.
42
Set the backsplash back into the dryer slots and push forward to lock in place.
43
Rethread the two screws.
44
Reattach the ground wire to the panel.
45
Insert the panel tabs into the slots on the dryer.
46
Rethread the five screws.
47
Plug in the dryer, and your dryer should be ready for use.
Applicable Product Model
Parts Needed
Felt Seal
$34.51
Recommended Tools and Accessories
Drum Slide Glide or Pad
$13.19
Drum Slide Glide or Pad
$19.98
Multi Screwdriver
$59.00
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com