Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dishwasher Mounting Bracket Replacement #WX13X10001
GE Dishwasher Mounting Bracket Replacement #WX13X10001
Skill Level
Total Parts Cost
$21.66Estimated Savings
$112.5004:18
- Description
This video provides step-by-step instructions for replacing the mounting bracket on GE dishwashers. The most common reason for replacing the mounting brackets is if they are misplaced while moving the dishwasher.
All of the information in this mounting bracket replacement video is applicable to the following brands: GE, Hotpoint, Kenmore
All of the information in this mounting bracket replacement video is applicable to the following brands: GE, Hotpoint, Kenmore
Step By Step Instructions
1
To replace the mounting brackets, you will need to uninstall the dishwasher first.
2
To do this, turn off the power supply to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panels and set the panels aside.
5
Disconnect the water supply line from the inlet valve.
6
Be prepared for some water to spill out.
7
Remove the screw to release the terminal block cover plate.
8
Note the location of the wires then untwist the wire nut to disconnect the wires.
9
Loosen the screw to release the grounding wire.
10
Use a flathead screwdriver to help remove the strain relief nut and pull the wires out of the junction box.
11
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the leveling legs to lower the appliance.
14
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
15
Remove the screws to release the old mounting brackets if still intact.
16
You’re now ready to install the new mounting brackets.
17
Align the appropriate bracket with the screw holes in the frame and use the provided screws to secure.
18
Repeat for the opposite side.
19
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
20
Adjust the leveling legs if necessary.
21
Replace the screws to secure the new mounting brackets to the cabinet.
22
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
23
Make sure the hose is elevated above the connection point.
24
Feed the wires back through the junction box and secure the strain relief nut.
25
Connect the wires using the wire nuts and secure the grounding wire with the screw.
26
Align the cover plate and replace the screw to secure.
27
Reconnect the water supply line to the inlet valve.
28
Replace the lower access panels and secure them with the screws.
29
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.
Description
This video provides step-by-step instructions for replacing the mounting bracket on GE dishwashers. The most common reason for replacing the mounting brackets is if they are misplaced while moving the dishwasher.
All of the information in this mounting bracket replacement video is applicable to the following brands: GE, Hotpoint, Kenmore
All of the information in this mounting bracket replacement video is applicable to the following brands: GE, Hotpoint, Kenmore
Step-By-Step Instructions
1
To replace the mounting brackets, you will need to uninstall the dishwasher first.
2
To do this, turn off the power supply to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panels and set the panels aside.
5
Disconnect the water supply line from the inlet valve.
6
Be prepared for some water to spill out.
7
Remove the screw to release the terminal block cover plate.
8
Note the location of the wires then untwist the wire nut to disconnect the wires.
9
Loosen the screw to release the grounding wire.
10
Use a flathead screwdriver to help remove the strain relief nut and pull the wires out of the junction box.
11
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
12
Open the dishwasher door and remove the mounting bracket screws.
13
To move the dishwasher, you may need to adjust the leveling legs to lower the appliance.
14
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
15
Remove the screws to release the old mounting brackets if still intact.
16
You’re now ready to install the new mounting brackets.
17
Align the appropriate bracket with the screw holes in the frame and use the provided screws to secure.
18
Repeat for the opposite side.
19
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
20
Adjust the leveling legs if necessary.
21
Replace the screws to secure the new mounting brackets to the cabinet.
22
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
23
Make sure the hose is elevated above the connection point.
24
Feed the wires back through the junction box and secure the strain relief nut.
25
Connect the wires using the wire nuts and secure the grounding wire with the screw.
26
Align the cover plate and replace the screw to secure.
27
Reconnect the water supply line to the inlet valve.
28
Replace the lower access panels and secure them with the screws.
29
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com