Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Dishwasher Impeller & Seal Kit Installation #WD19X10038
GE Dishwasher Impeller & Seal Kit Installation #WD19X10038
Skill Level
Total Parts Cost
$52.83Estimated Savings
$112.5007:16
- Description
This video provides step-by-step instructions for installing the impeller and seal kit for GE and Hotpoint dishwashers. The most common reason for replacing the parts the kit contains is when the dishwasher is leaking water from the motor area.
All of the information in this impeller and seal kit installation video is applicable to the following brands: GE, Hotpoint
All of the information in this impeller and seal kit installation video is applicable to the following brands: GE, Hotpoint
Step By Step Instructions
1
To replace the impeller and seal components, you will need to uninstall the dishwasher first.
2
To do this, turn off the power supply to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panels and set the panels aside.
5
Disconnect the water supply line from the inlet valve.
6
Be prepared for some water to spill out.
7
Remove the screw to release the terminal block cover plate.
8
Note the location of the wires then untwist the wire nuts to disconnect the wires.
9
Use a flathead screwdriver to help remove the strain relief nut and pull the wires out of the junction box.
10
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
11
Open the dishwasher door and remove the mounting bracket screws.
12
To move the dishwasher, you may need to adjust the leveling legs to lower the appliance.
13
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
14
Carefully tilt the dishwasher back so its rear panel rests on a blanket or carpet.
15
Next, disconnect the wire harnesses from the drain solenoid and the motor.
16
Remove the screw the release the support rod.
17
Loosen the clamp securing the chamber hose to the pump housing and pull the hose off.
18
Next, loosen the pump connector and pump housing clamps and pull the pump and motor assembly free.
19
Next, use pliers to secure the motor shaft as you rotate the cutting blade counter-clockwise to remove.
20
Use a putty knife to remove the suction ring by rotating it clockwise.
21
Lift out the wear ring and retainer.
22
Now, secure the motor shaft and rotate the impeller counter-clockwise to remove.
23
Remove the mounting screws securing the motor and separate the motor from the pump housing.
24
Use a screwdriver to help push out the seal.
25
You’re now ready to install the new impeller and seal components.
26
Press the new seal into the pump housing.
27
Position the motor and secure it with the mounting screws.
28
Secure the motor shaft and rotate the impeller clockwise to install.
29
Replace the wear ring and retainer.
30
Thread the suction ring into place and use the putty knife to tighten.
31
Thread the cutting blade into place flange side down and tighten with the pliers.
32
Reinstall the pump and motor assembly by inserting the larger inlet port into the sump and the smaller outlet port into the pump connector.
33
Tighten the clamps to secure.
34
Connect the chamber hose and secure the clamp.
35
Align the support rod and secure it with the screw.
36
Reconnect the wire harnesses to both the motor and the drain solenoid.
37
Now carefully lift the dishwasher to its upright position.
38
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
39
Adjust the leveling legs if necessary.
40
Replace the screws to secure the mounting brackets to the cabinet or countertop.
41
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
42
Make sure the hose is elevated above the connection point.
43
Feed the wires back through the junction box and secure the strain relief nut.
44
Connect the wires using the wire nuts.
45
Align the cover plate and replace the screw to secure.
46
Reconnect the water supply line to the inlet valve.
47
Replace the lower access panels and secure them with the screws.
48
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.
Description
This video provides step-by-step instructions for installing the impeller and seal kit for GE and Hotpoint dishwashers. The most common reason for replacing the parts the kit contains is when the dishwasher is leaking water from the motor area.
All of the information in this impeller and seal kit installation video is applicable to the following brands: GE, Hotpoint
All of the information in this impeller and seal kit installation video is applicable to the following brands: GE, Hotpoint
Step-By-Step Instructions
1
To replace the impeller and seal components, you will need to uninstall the dishwasher first.
2
To do this, turn off the power supply to your dishwasher
3
Shut off the water supply valve.
4
Next, remove the screws to release the lower access panels and set the panels aside.
5
Disconnect the water supply line from the inlet valve.
6
Be prepared for some water to spill out.
7
Remove the screw to release the terminal block cover plate.
8
Note the location of the wires then untwist the wire nuts to disconnect the wires.
9
Use a flathead screwdriver to help remove the strain relief nut and pull the wires out of the junction box.
10
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
11
Open the dishwasher door and remove the mounting bracket screws.
12
To move the dishwasher, you may need to adjust the leveling legs to lower the appliance.
13
Now, to avoid damage, very carefully pull the dishwasher away from the cabinet.
14
Carefully tilt the dishwasher back so its rear panel rests on a blanket or carpet.
15
Next, disconnect the wire harnesses from the drain solenoid and the motor.
16
Remove the screw the release the support rod.
17
Loosen the clamp securing the chamber hose to the pump housing and pull the hose off.
18
Next, loosen the pump connector and pump housing clamps and pull the pump and motor assembly free.
19
Next, use pliers to secure the motor shaft as you rotate the cutting blade counter-clockwise to remove.
20
Use a putty knife to remove the suction ring by rotating it clockwise.
21
Lift out the wear ring and retainer.
22
Now, secure the motor shaft and rotate the impeller counter-clockwise to remove.
23
Remove the mounting screws securing the motor and separate the motor from the pump housing.
24
Use a screwdriver to help push out the seal.
25
You’re now ready to install the new impeller and seal components.
26
Press the new seal into the pump housing.
27
Position the motor and secure it with the mounting screws.
28
Secure the motor shaft and rotate the impeller clockwise to install.
29
Replace the wear ring and retainer.
30
Thread the suction ring into place and use the putty knife to tighten.
31
Thread the cutting blade into place flange side down and tighten with the pliers.
32
Reinstall the pump and motor assembly by inserting the larger inlet port into the sump and the smaller outlet port into the pump connector.
33
Tighten the clamps to secure.
34
Connect the chamber hose and secure the clamp.
35
Align the support rod and secure it with the screw.
36
Reconnect the wire harnesses to both the motor and the drain solenoid.
37
Now carefully lift the dishwasher to its upright position.
38
Make sure the end of the drain hose is accessible through the cabinet wall then gently slide the dishwasher back into the cabinet.
39
Adjust the leveling legs if necessary.
40
Replace the screws to secure the mounting brackets to the cabinet or countertop.
41
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
42
Make sure the hose is elevated above the connection point.
43
Feed the wires back through the junction box and secure the strain relief nut.
44
Connect the wires using the wire nuts.
45
Align the cover plate and replace the screw to secure.
46
Reconnect the water supply line to the inlet valve.
47
Replace the lower access panels and secure them with the screws.
48
You’re now ready to turn the water supply back on as well as the power and confirm that the dishwasher is functioning properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com