Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Drain Pump Replacement WH23X28418
This video provides step-by-step repair instructions for replacing the drain pump in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Drain Pump Replacement WH23X28418
Skill Level
Total Parts Cost
$47.34Estimated Savings
$112.5004:52
- Description
This video provides step-by-step repair instructions for replacing the drain pump in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the drain pump on your ge washer, you will need an impact driver with a 1/4” bit, pliers a 3/8” socket, needlenose pliers, and a 1/4” socket adapter.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves.
6
Tip the washer back and prop it up using a wooden block or chair.
7
Unthread the three screws holding the protective belt cover to remove it.
8
Pull the wire retaining clip from the transmission housing and unplug the drain pump.
9
Slide down the clamp securing the hose to the drain pump.
10
Slide the hose off of the drain pump.
11
Unthread the three screws holding the drain pump in place.
12
Detatch the drain pump.
13
To install the new drain pump, attach the pump to the tub.
14
Rethread the three screws.
15
Connect the hose to the drain pump, then slide the clamp to secure it.
16
Plug in the drain pump and then secure it with the wire retaining clip.
17
Align the cover and start one of the three screws.
18
Place the grounding connector over the screw and rethread it to the bottom of the transmission.
19
Now rethread the last screw.
20
Prop up the washer.
21
Reattatch the hot and cold-water supply lines.
22
Insert the drain hose back into the wall drain.
23
Turn on the water supply
24
Plug in the power.
Description
This video provides step-by-step repair instructions for replacing the drain pump in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the drain pump in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the drain pump on your ge washer, you will need an impact driver with a 1/4” bit, pliers a 3/8” socket, needlenose pliers, and a 1/4” socket adapter.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valves.
6
Tip the washer back and prop it up using a wooden block or chair.
7
Unthread the three screws holding the protective belt cover to remove it.
8
Pull the wire retaining clip from the transmission housing and unplug the drain pump.
9
Slide down the clamp securing the hose to the drain pump.
10
Slide the hose off of the drain pump.
11
Unthread the three screws holding the drain pump in place.
12
Detatch the drain pump.
13
To install the new drain pump, attach the pump to the tub.
14
Rethread the three screws.
15
Connect the hose to the drain pump, then slide the clamp to secure it.
16
Plug in the drain pump and then secure it with the wire retaining clip.
17
Align the cover and start one of the three screws.
18
Place the grounding connector over the screw and rethread it to the bottom of the transmission.
19
Now rethread the last screw.
20
Prop up the washer.
21
Reattatch the hot and cold-water supply lines.
22
Insert the drain hose back into the wall drain.
23
Turn on the water supply
24
Plug in the power.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com