Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Top Load Washer Transmission Replacement #134736400
Frigidaire Top Load Washer Transmission Replacement #134736400
Skill Level
Total Parts Cost
$682.06Estimated Savings
$112.5006:30
- Description
This video provides step-by-step instructions for replacing the transmission on Frigidaire top loading washing machines. The most common reasons for replacing the transmission are when the washer is not spinning, agitating or is making loud noises.
All of the information in this transmission replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Kelvinator, Tappan, Universal, Crosley, Montgomery Wards
All of the information in this transmission replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Kelvinator, Tappan, Universal, Crosley, Montgomery Wards
Step By Step Instructions
1
As with any repair, you should unplug the appliance before beginning.
2
To replace the washer’s transmission, you should first secure the lid with tape.
3
Now insert a putty knife under the main top to release the two spring clips.
4
Lift up the main top and support it.
5
Next, remove the mounting screws at the bottom of the front panel.
6
Push the panel down and pull it away from the frame.
7
Reach under the tub and depress the idler pulley to release the tension on the drive belt then remove the belt from the pulleys.
8
Next, pull off the dispenser cover and cup.
9
Use a half-inch socket to remove the agitator bolt and lift off the agitator.
10
This may require some effort.
11
Detach the pressure switch tube from the tub cover.
12
Use a flathead screwdriver to help release the tabs to remove the tub cover.
13
Use the half-inch socket to remove the trunnion block mounting bolts and pull the block off.
14
You can now lift out the inner tub.
15
Push the brass ring down to detach it from the gasket then slide the ring and gasket off of the drive tube.
16
Next, remove the screws securing the motor shield and move the shield and capacitor to the side.
17
Release the clamp securing the hose to the tub port and pull the hose off.
18
Be prepared for water to spill out.
19
Remove the pressure switch tube from the outer tub.
20
Now, remove the outer tub mounting bolts.
21
Note the orientation of the outer tub then lift it off of the drive tube.
22
Remove the spacer.
23
Use a 3/8th inch socket to remove the set screw securing the transmission pulley then pull out the pulley.
24
Use the 3/8th inch socket to remove the bolts holding the transmission bearing block to the mounting plate.
25
Lift out the old transmission.
26
Prepare the new transmission for installation by pre-threading the provided bolts into the transmission bearing block.
27
Remove the bolts position the new transmission on the mounting plate and rethread the bolts to secure.
28
Slide on the provided drive block if applicable; otherwise, use the existing block.
29
Position the transmission pulley on the drive shaft and secure it with the new set screw.
30
Replace the spacer.
31
Reposition the outer tub on the drive tube and secure it with the mounting bolts.
32
Reattach the pressure switch tube to the outer tub.
33
Reconnect the hose to the tub port and secure it with the clamp.
34
Reposition the capacitor and motor shield and reinstall the screws to secure.
35
Slide the brass ring and gasket onto the drive tube and press the gasket firmly into the ring.
36
Replace the inner tub.
37
Align the trunnion block on the spin tube slot and secure with the mounting bolts.
38
Align the tabs on the tub cover with the catches on the outer tub and snap the cover into place.
39
Reattach the pressure switch tube.
40
Slide the agitator onto the drive block and secure with the bolt.
41
Replace the dispenser cup and cover.
42
Replace the drive belt by hooking it onto the motor and idler pulleys then rotate the transmission pulley to fully align the belt.
43
Replace the front panel by aligning the tabs on the panel with the slots in the frame then lift the panel up.
44
Replace the mounting screws to secure.
45
Remove the support lower the main top and snap it into place.
46
Then remove the tape securing the lid.
47
You’re now ready to plug the power cord back in and confirm that the washer is functioning properly.
Description
This video provides step-by-step instructions for replacing the transmission on Frigidaire top loading washing machines. The most common reasons for replacing the transmission are when the washer is not spinning, agitating or is making loud noises.
All of the information in this transmission replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Kelvinator, Tappan, Universal, Crosley, Montgomery Wards
All of the information in this transmission replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Kelvinator, Tappan, Universal, Crosley, Montgomery Wards
Step-By-Step Instructions
1
As with any repair, you should unplug the appliance before beginning.
2
To replace the washer’s transmission, you should first secure the lid with tape.
3
Now insert a putty knife under the main top to release the two spring clips.
4
Lift up the main top and support it.
5
Next, remove the mounting screws at the bottom of the front panel.
6
Push the panel down and pull it away from the frame.
7
Reach under the tub and depress the idler pulley to release the tension on the drive belt then remove the belt from the pulleys.
8
Next, pull off the dispenser cover and cup.
9
Use a half-inch socket to remove the agitator bolt and lift off the agitator.
10
This may require some effort.
11
Detach the pressure switch tube from the tub cover.
12
Use a flathead screwdriver to help release the tabs to remove the tub cover.
13
Use the half-inch socket to remove the trunnion block mounting bolts and pull the block off.
14
You can now lift out the inner tub.
15
Push the brass ring down to detach it from the gasket then slide the ring and gasket off of the drive tube.
16
Next, remove the screws securing the motor shield and move the shield and capacitor to the side.
17
Release the clamp securing the hose to the tub port and pull the hose off.
18
Be prepared for water to spill out.
19
Remove the pressure switch tube from the outer tub.
20
Now, remove the outer tub mounting bolts.
21
Note the orientation of the outer tub then lift it off of the drive tube.
22
Remove the spacer.
23
Use a 3/8th inch socket to remove the set screw securing the transmission pulley then pull out the pulley.
24
Use the 3/8th inch socket to remove the bolts holding the transmission bearing block to the mounting plate.
25
Lift out the old transmission.
26
Prepare the new transmission for installation by pre-threading the provided bolts into the transmission bearing block.
27
Remove the bolts position the new transmission on the mounting plate and rethread the bolts to secure.
28
Slide on the provided drive block if applicable; otherwise, use the existing block.
29
Position the transmission pulley on the drive shaft and secure it with the new set screw.
30
Replace the spacer.
31
Reposition the outer tub on the drive tube and secure it with the mounting bolts.
32
Reattach the pressure switch tube to the outer tub.
33
Reconnect the hose to the tub port and secure it with the clamp.
34
Reposition the capacitor and motor shield and reinstall the screws to secure.
35
Slide the brass ring and gasket onto the drive tube and press the gasket firmly into the ring.
36
Replace the inner tub.
37
Align the trunnion block on the spin tube slot and secure with the mounting bolts.
38
Align the tabs on the tub cover with the catches on the outer tub and snap the cover into place.
39
Reattach the pressure switch tube.
40
Slide the agitator onto the drive block and secure with the bolt.
41
Replace the dispenser cup and cover.
42
Replace the drive belt by hooking it onto the motor and idler pulleys then rotate the transmission pulley to fully align the belt.
43
Replace the front panel by aligning the tabs on the panel with the slots in the frame then lift the panel up.
44
Replace the mounting screws to secure.
45
Remove the support lower the main top and snap it into place.
46
Then remove the tape securing the lid.
47
You’re now ready to plug the power cord back in and confirm that the washer is functioning properly.
Applicable Product Model
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com