Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeChoose Product
Identify Problem
03
Find Solutions
HomeRepair HelpInglis Dryer RepairInglis Dryer won't start Repair
Inglis Dryer won't start
If your Inglis dryer won't start, the most likely culprits are a blown thermal fuse, a door that is not fully closed, or a faulty start switch, with door switch problems, a bad control board, or an object stuck in the blower wheel less likely but still possible. Start by checking the thermal fuse for continuity with a multimeter and inspect the venting; a blown thermal fuse usually means the dryer overheated because the exhaust is restricted. Make sure the door is fully closed and nothing is blocking the latch. If the dryer is dead, test the start switch for continuity, noting that a humming motor usually means the switch is not the issue. Listen for a click from the door switch when you close the door and test it if you don’t hear one. If those checks fail, visually inspect the control board for damage and verify voltage to the motor, and remove the blower cover to look for clothing caught in the blower wheel. Enter your model number on RepairClinic.com to find the exact replacement part for your dryer.
01 - Inglis Dryer Thermal Fuse
The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check t...
Enter model number to search for the required part specific to your product
Top Solution
02 - Door is not fully closed
Since the dryer will not start with the door open, confirm the door is fully closed and remove anything that is obstructing the door.
Top Solution
03 - Inglis Dryer Start Switch
To determine if the start switch is defective, attempt to start the dryer. If the dryer hums but does not start, the start switch is not at fault. If the dryer does not respond or make any noise, the start switch could be at fault. Use a multimeter to test the start switch for continuity. If the switch does not have continuity, replace it.
Highly Likely
04 - Inglis Dryer Door Switch
The door switch activates when the dryer door is closed. On most dryers, the door switch makes an audible clicking sound when it activates. To determine if the door switch is working, try starting your dryer and then listen for the “click.” If the door switch makes a clicking sound, it is probably not defective. If you don’t hear a click, use a multimeter to use the door switch for continuity. If the switch does not have continuity, replace it.
Common
05 - Inglis Dryer Control Board
A dryer's control board controls the voltage being sent to all of the appliance's electrical components. If the board is defective, it may not allow the dryer to start. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to test for voltage reaching the drive motor after reviewing the dryer's wiring diagram.
Common
06 - Object stuck in blower wheel
If the dryer won’t start, an article of clothing may have gotten past the lint screen and is caught in the blower wheel. When this happens the drive motor will either hum but won’t start or will make a lot of noise when trying to start. The blower cover will need to be removed to check for obstructions. If the blower wheel is damaged it will need to be replaced.
Common
Frequently Asked Questions
Why won't my Inglis dryer start?
My dryer hums but the drum won't turn. What should I check?
Why is my dryer making a grinding or loud noise when the drum turns?
Could a blown thermal fuse cause the dryer to stop starting and how do I test it?
How do I enter my model number on RepairClinic.com to find the correct replacement part?
Shop by Inglis Dryer Parts
Shop by Popular Inglis Dryer Models
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com