Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeChoose Product
Identify Problem
03
Find Solutions
HomeRepair HelpGaggenau Dryer RepairGaggenau Dryer overheating Repair
Gaggenau Dryer overheating
If your Gaggenau dryer is running too hot or overheating, start by checking the heating element or heating element assembly—partial shorts in the element are the most common cause and can make the dryer heat continuously even when the cycle is off. Use a multimeter to test element continuity and to check for continuity to the case; any continuity to the case means the element is shorted and should be replaced. A stuck timer contact can also feed voltage to the heater, though that is rare, so only replace the timer after testing the more likely parts. Poor airflow from a clogged vent or lint buildup will raise cabinet temperature and can cause a burning smell, so inspect and clean the venting system and outdoor hood. If the dryer overheats and then shuts off until it cools, the drive motor may be failing. A bad thermistor or temperature sensor can falsely report temperature to the control and allow overheating as well. If you need parts, enter your model number on RepairClinic.com to find the exact replacement for your dryer.
01 - Gaggenau Dryer Heating Element
The heating element warms the air before the air enters the dryer drum. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, use a multimeter to test each terminal for continuity to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it.
Enter model number to search for the required part specific to your product
Top Solution
02 - Gaggenau Dryer Heating Element Assembly
The heating element warms air as it passes over the element. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, first use a multimeter to test the heating element for continuity. If the heating element does not have continuity, replace it. Next, test for continuity from each terminal to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it.
Top Solution
03 - Gaggenau Dryer Timer
A dryer that is overheating could be caused by a faulty timer allowing continuous voltage to be sent to the heating circuit. If the timer's heating contacts and the heating element are shorted, the heating element can heat when the timer is off. However, this is very rarely the case. Before replacing the timer, check all the more commonly defective parts. If you determine that all of the other components are working properly, test the timer by using a multimeter and consulting the wiring diagram. If the timer is defective, replace it.
Top Solution
04 - Air Flow Problem
If the vent line is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time and cabinet temperature and potentially causing a burning smell. To ensure proper dryer performance, you should clean your dryer's venting system at least once per year.
Top Solution
05 - Gaggenau Dryer Drive Motor
A dryer's drive motor will drive the drum belt to rotate the drum as well as spin a blower wheel to circulate the air through the drum during operation. If the dryer runs for a while and then stops, and won't start again until it cools down, it's likely the drive motor is malfunctioning and will need to be replaced.
Highly Likely
06 - Gaggenau Dryer Thermistor
A dryer thermistor monitors the dryer temperature and sends a resistance reading to the control board. If the thermistor is malfunctioning, it may fail to send the correct reading to the control board resulting in the dryer overheating. If you've determined there is good air flow coming out the home's outside vent hood and the dryer venting is free of obstructions, the thermistor is one of the components you can test for electrical continuity with a multimeter to see if it's functioning properly. While the thermistor should have continuity at room temperature, the ohm’s reading should go lower as the temperature on the sen...
Highly Likely
Frequently Asked Questions
Why is my dryer overheating and shutting off?
My dryer starts then stops and won’t start again until it cools. What’s wrong?
My dryer is running too hot and smells like something is burning. What should I check?
Why is my dryer taking too long to dry?
How do I find the right replacement part using my model number or a part number on RepairClinic?
Shop by Gaggenau Dryer Parts
Shop by Popular Gaggenau Dryer Models
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com