Choose Product
Identify Problem
03
Find Solutions

Maytag Dryer won't stop

If your Maytag dryer won't stop or keeps running long after the cycle ends, the most common cause is restricted airflow from a clogged or partially blocked vent. Poor venting raises cabinet temperature and drying time, so start by checking and cleaning the vent and lint trap. If the vent is clear, make sure the anti-wrinkle or similar option was not selected, since that setting tumbles the drum every few minutes after a cycle and will make it seem like the dryer won’t stop. A stuck or worn blower wheel is next likely; lint or small garments can jam the wheel or a worn sleeve can make it wobble and reduce airflow. Less commonly a loose power plug or a tripped breaker can cause intermittent power that affects cycle timing, and a faulty control board can allow the dryer to keep running by sending incorrect voltage to the motor. If you need replacement parts — blower wheel, control board, venting components or others — enter your model number at RepairClinic.com to find the exact part that fits your dryer.

01 - Air Flow Problem

If the vent line is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time and cabinet temperature and potentially causing a burning smell. To ensure proper dryer performance, you should clean your dryer's venting system at least once per year.
Top Solution

02 - Anti-wrinkle cycle option selected

Most dryer models have an anti-wrinkle cycle option that can be selected to reduce wrinkles. When selected the dryer drum will tumble the clothes every few minutes after the cycle is completed to help keep wrinkles from occurring. If this option was inadvertently selected the dryer will intermittently run until the clothes are removed.
Top Solution

03 - Maytag Dryer Blower Wheel

The blower wheel draws air through the dryer and pushes the air out the vent. Clumps of lint, socks, and small articles of clothing can escape the lint filter and get caught in the blower wheel. In addition, the blower wheel sleeve can wear out, allowing the blower wheel to wobble on the motor shaft. If the blower wheel is obstructed or defective, it may take too long to dry clothes. To determine if the blower wheel is working properly, remove the dryer vent and assess the strength of the air flow. If the air flow is weak, check the blower wheel for obstructions. If no obstructions are present, try rotating the blower whee...l by hand. If the blower wheel wobbles as it turns, replace it.
Enter model number to search for the required part specific to your product
Top Solution

04 - Incoming Power Problem

Confirm a circuit breaker has not tripped and the power cord is plugged tightly into the wall receptacle. A loose plug can provide intermittent power to the dryer and cause it to spinning stop during the cycle.
Top Solution

05 - Maytag Dryer Control Board

A dryer's control board controls the voltage being sent to all of the appliance's electrical components. If there's no obstruction in the dryer's venting and the dryer is heating to the proper temperature, it's possible the control board is defective and allowing the appliance to run longer than it should. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to test for voltage reaching the drive motor after reviewing the dryer's wiring diagram.
Common

06 - Maytag Dryer Main Control Board

A dryer's main control board controls the voltage being sent to all of the appliance's electrical components. If there's no obstruction in the dryer's venting and the dryer is heating to the proper temperature, it's possible the control board is defective and allowing the appliance to run longer than it should. You can inspect the board for signs of damage or a shorted component.
Common

Frequently Asked Questions

Why won't my dryer stop running after the cycle finishes?
Can a clogged vent make my dryer keep running or take too long to dry?
How do I check the blower wheel if my dryer keeps running or runs too long?
My dryer starts then stops or the drum stops spinning during a cycle. Could it be a power problem?
How do I enter my model number or part number on RepairClinic.com to find the correct replacement part?