Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeChoose Product
Identify Problem
03
Find Solutions
HomeRepair HelpKitchenAid Oven RepairKitchenAid Oven temperature not accurate Repair
KitchenAid Oven temperature not accurate
When your KitchenAid oven temperature is not accurate, the bake element is the first part to check. A damaged element with holes or blisters, or one that lacks continuity, may not heat correctly and can cause an oven temperature problem. Next, inspect the oven control board, which controls voltage to the bake and broil elements or igniters. A faulty board can shut the heating circuit off too early or fail to regulate heat. Before replacing parts, verify the temperature with a dial or digital thermometer after the oven cycles at 350°F for at least 20 minutes. If the reading is within about 35°F of the setting, oven calibration may correct the issue. If your gas KitchenAid oven runs too cold, a weak oven igniter may delay burner relighting and cause temperature swings. A defective gas oven control module or spark module can also interfere with heating. Test the oven sensor, thermostat, wiring, and related components before replacing a control. Enter your model number to find the exact replacement bake element, control board, igniter, or other part for your KitchenAid range, stove, or oven.
01 - KitchenAid Range/Stove/Oven Bake Element
When the bake element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element is not heating. Often, if the heating element has burned out, it will be visibly damaged. Inspect the heating element for holes or blisters. To determine if the bake element has burned out, use a multimeter to test the element for continuity. If the bake element does not have continuity, replace it.
Enter model number to search for the required part specific to your product
Top Solution
02 - KitchenAid Range/Stove/Oven Control Board
An oven's control board will often be used to send voltage to the bake and broil elements or the igniters to heat the oven to the designated temperature. When a temperature sensor senses that the oven has reached the appropriate temperature, the control board should shut off the voltage to the heating circuit. If the control board is defective, the voltage may be shut off too early or not at all, resulting in an inaccurate oven temperature. You should test the temperature sensor and other components first before considering replacing the control board. If you confirm the other components are working properly, you can inspe...
Top Solution
03 - Oven calibration needed
It is normal for oven temperature to fluctuate throughout the cooking process. Oven temperature can be verified by using a dial thermometer or a digital thermometer with the wire lead end touching a cast iron skillet placed in the oven to keep the temperature reading even. Heat the oven to 350 degrees Fahrenheit (177 degrees Celsius). Let the oven cycle on and off for at least 20 minutes, then check the temperature. If the oven temperature is over or under by 35 degrees Fahrenheit (2 degrees Celsius) the oven thermostat, oven sensor, or oven control (depending on the model), is likely at fault. If the temperature is within 35 degrees (2 degrees Celsius) above or below the set temperature, it can likely be recalibrated succcessfully. Refer to your owner's manual for instructions.
Top Solution
04 - KitchenAid Range/Stove/Oven Igniter
The igniter draws electrical current through the gas valve to open it. As the igniter weakens over time, it takes longer to open the gas valve. As a result, the oven temperature will drop too low before the burner reignites. The oven temperature should not drop more than 40 degrees Fahrenheit before the igniter relights the burner.
Highly Likely
05 - KitchenAid Range/Stove/Oven Control Module
A gas oven's control module will often be used to send voltage to the igniters to heat the oven to the designated temperature. When a temperature sensor senses that the oven has reached the appropriate temperature, the control module should shut off the voltage to the heating circuit. If the module is defective, the voltage may be shut off too early or not at all, resulting in an inaccurate oven temperature. You should test the temperature sensor and other components first before considering replacing the control module. If you confirm the other components are working properly, you can inspect the module for signs of damag...
Common
06 - KitchenAid Range/Stove/Oven Spark Module
For gas ovens using a spark igniter, a faulty spark module could be responsible for the oven not heating. If you do not see a spark near the bake or broiler burner tube when the oven is turned on, use a multimeter to determine if voltage is reaching the spark module. If power is present, the spark module is likely defective and will need to be replaced.
Common
Frequently Asked Questions
Why is my KitchenAid oven temperature not accurate?
How do I check whether my KitchenAid oven needs calibration?
How do I test the temperature sensor on a KitchenAid oven?
Why is my KitchenAid gas oven running cold even though the igniter glows?
How do I find the correct KitchenAid oven temperature sensor or bake element?
Shop by Popular KitchenAid Range/Stove/Oven Models
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com