Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeChoose Product
Identify Problem
03
Find Solutions
HomeRepair HelpRoper Oven RepairRoper Gas stove burners spark all the time Repair
Roper Gas stove burners spark all the time
If your Roper gas stove igniter keeps clicking or the gas stove keeps sparking after the burner lights, a defective spark ignition switch is the most likely cause. Test each switch with a multimeter for continuity. A switch that shows continuity at every dial setting is stuck closed and should be replaced. The spark ignition switch and harness can also be wet or shorted, especially after a boil-over, so unplug the range and let the stovetop dry completely before testing. Next, inspect the surface burner orifice holder. If it is misaligned, it may not ground correctly, preventing the spark module from sensing the flame. Make sure each burner cap is seated properly on its burner base, since a misplaced cap can keep gas or flame away from the spark electrode. If the burner still won't stop sparking, inspect the spark electrode for dirt or visible damage. A faulty electrode may fail to sense the flame even when the burner is lit. Enter your Roper range model number to find the exact spark ignition switch, harness, or spark electrode replacement part for your appliance.
01 - Roper Range/Stove/Oven Spark Ignition Switch
One of the spark ignition switches might be defective. The spark ignition switch sends voltage to the spark module. When the electrical contacts inside the switch close, power flows to the spark module. If the spark ignition switch fails with the electrical contacts closed, the switch will send continuous voltage to the spark module. To determine if any of the spark ignition switches is defective, use a multimeter to test each of the switches for continuity. If a spark ignition switches shows continuity at all settings, replace it.
Enter model number to search for the required part specific to your product
Top Solution
02 - Roper Range/Stove/Oven Spark Ignition Switch and Harness
One of the spark ignition switches might be defective. The spark ignition switch sends voltage to the spark module. When the electrical contacts inside the switch close, power flows to the spark module. If the switch contacts are wet or stuck in a closed position, the switch will send continuous voltage to the spark module, no matter where the dial is set. Each of the switches can be tested individually to determine if they are shorted. If a spark ignition switch is shorted and is not wet, or if drying it out doesn’t solve the problem, replace the switch.
Top Solution
03 - Roper Range/Stove/Oven Surface Burner Orifice Holder
Some burners have a flame sensing circuit that sense the burner flame through the spark electrode circuit. If the burner has a good flame but the igniter keeps sparking the orifice holder may not be damaged and not grounding properly. Inspect the holder to see if it's misaligned and replace with a new one as required.
Top Solution
04 - Burner cap not on properly
On some models the spark module will automatically shut off the spark when the burner lights. If the burner cap is not on properly the gas or flame may not get to the igniter causing continuous sparking. Confirm the appliance is turned off and the stovetop is cool to the touch, then readjust the burner cap, if necessary, so it is seated properly on the burner base.
Top Solution
05 - Water spilt on switches
The spark switches under the burner knobs have to be dry to work properly. If water boils over or is spilt on the spark switches, they can short out, causing the burners to spark even when the switch is turned off. The range should be unplugged and the stovetop allowed a day to dry out.
Common
06 - Roper Range/Stove/Oven Spark Electrode
The range's spark module sends pulses to each spark electrode to create a spark to ignite the gas. If the spark module has a flame sensing function it will automatically stop sending pulses to the electrode when the burner lights. If the electrode is defective the spark module will not be able to sense the flame and continue to allow the electrode to spark after the flame has ignited. Inspect the electrode to see if it's visibly damaged or dirty and replace if necessary.
Common
Frequently Asked Questions
Why do my Roper gas stove burners keep sparking?
How do I test a Roper spark ignition switch?
Why does my gas stove keep sparking after the burner lights?
What should I check if water spilled on my Roper gas stove switches?
How do I find the correct Roper spark ignition switch or electrode?
Shop by Popular Roper Range/Stove/Oven Models
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com